User manual ICOM IC-12A

[. . . ] No risk of personal injury, fire or electric shock. WORD [For IC-12A only] Dualwatch operation/Diversity operation DV and P25, Digital modes are available (Only when the specific digital unit is installed. ) MOUSE PROPERTY SETTING Depending on the `Mouse Property' setting in the control panel, main and sub mouse button functions are swapped. In this instruction manual, the operation is described with the default setting. Icom, Icom Inc. and the logo are registered trademarks of Icom Incorporated (Japan) in the United States, the United Kingdom, Germany, France, Spain, Russia and/or other countries. i SYSTEM REQUIREMENTS PC · Microsoft® Windows® XP/2000/Me/98SE installed · USB 2. 0 or 1. 1 · Intel Pentium® III 450 MHz or faster (Pentium® 4 recommended) · At least 128 MB of memory or higher (256 MB or more recommended) · At least 50 MB or higher hard disk space · At least 1024 × 768 pixel resolution, high color display · CD-ROM or DVD drive is required for software installation. [. . . ] Indicators MONI MUTE · [Compo] screen IC-PCR1500 MAIN MONI SUB Indicators MUTE · [Receiver] screen IC-PCR1500 IC-12A zMONIx zMUTEx Mute function This function is used to mute the received audio signal. Click zMUTEx to temporarily mute audio output. · "MUTE" appears when [Receiver]/[Compo] screen is displayed. · "MUTE" button lights green when [Simple] screen is displayed. IC-12A zMONIx zMUTEx MODE/VOL PANEL MAIN SUB Indicators MONI MUTE · [Simple] screen IC-PCR1500 IC-12A zMUTEx MAIN SUB zMONIx 56 BASIC RECEIVE FUNCTIONS 5 Duplex operation Duplex communication uses one frequency for transmit, and a different frequency for receive. Generally, duplex is used in communication through a repeater, some utility communications, etc. During duplex operation, the transmit station frequency is shifted from the receive station frequency by the offset frequency. Repeater information (offset frequency and shift direction) can be programmed into memory channels. 68) qSet the receive frequency (repeater output frequency). 48) wRight click zDUPx to display the [DUP Offset] screen. eSet the desired offset frequency within 0. 000000­ 1000. 000000 MHz range, then click the close button ([X]) to close the setting screen. rLeft click zDUPx to toggle the duplex direction from OFF (simplex), DUP­ or DUP+. ·" set. " or " " appears when the duplex direction is · [Receiver] screen IC-PCR1500 IC-12A zMONIx 5 MAIN SUB zDUPx · [DUP Offset] screen · [Compo] screen IC-PCR1500 IC-12A zDUPx zMONIx TUNING PANEL MODE/VOL PANEL MAIN SUB tClick zMONIx to monitor the transmit station frequency (repeater input frequency). qRight-click the zWXx button to call up the [WX Alert] screen. wSelect the desired weather channel in [WX Alert Channel]. · Click zCHECKx to monitor the selected weather channel. eClick the close ([X]) button to close the [WX Alert] screen. r Click the zWXx button to turn the weather alert function ON. t When the alert is detected, a beep sounds and the indication will be displayed as at right. y Click the zWXx button to turn the weather alert function OFF. NOTE: While receiving a signal (on a frequency other than the weather alert ON frequency), the receiving signal or audio will be interrupted momentarily every 5 sec. (approx. ) in case the alert function is turned ON. This symptom is caused by the WX alert function. To cancel these symptoms, set the weather alert item to OFF in set mode. [. . . ] 70, 86 memory skip function in the desired channels. The Communication error · The computer does not recognize the connected · Launch the program after approx. IC-PCR1500_2500 pro- · The protector circuit of the power supply is acti- · Use the supplied AC adapter, or a stabilized power pgs. vated. 17 18 133 19 D GENERAL SPECIFICATIONS AND OPTIONS Specifications · Frequency coverage U. S. A. [. . . ]