User manual ICOM IC-12GE

[. . . ] NEVER connect the transcever to an AC outlet. Ths may pose a fire hazard or result n an electrc shock. NEVER connect the transcever to a power source of more than 16 V DC such as a 24 V battery. Ths connecton wll run the transcever. DO NOT operate the transcever wthout runnng the vehcle's engne. [. . . ] · [Call A] and/or [Call B] may be avalable when your system employs selectve `Indvdual/Group' calls. Ask your dealer whch call s assgned to each key. SURVEILLANCE KEY Push to turn the survellance functon ON or OFF. When ths functon s turned ON, the beep s not emtted and the LCD backlght does not lght when a sgnal s receved or a key s pushed, etc. TX CODE ENTER KEY (PMR operaton only) Push to enter the TX code edt mode drectly. Then set the desred dgt usng [CH Up]/[CH Down]. 10) 5 1 PANEL DESCRIPTION USER SET MODE KEY Push and hold for 1 sec. to enter user set mode. · Durng user set mode, push ths key to select an tem*, and change the value or condton usng [CH Up]/[CH Down]. *Selectable tems may dffer dependng on the pre-settng. TX CODE CHANNEL SELECT KEY Push to enter the TX code channel selecton mode. Then set the desred channel usng [CH Up]/[CH Down]. 9) Whle n the TX code channel selecton mode, push and hold ths key for 1 sec. Then set the desred dgt usng [CH Up]/[CH Down]. · . enalty timer Once the tme-out tmer s actvated, transmsson s further nhbted for a perod determned by the penalty tmer. · . TTID call The transcever sends the ID code (5-tone, DTMF or dgtal ANI) automatcally when [PTT] s pushed (begnnng of the transmsson) and/or released (end of transmsson) dependng on the settng. PTTID call s also avalable wth the MDC 1200 sgnalng system. 13) r Push [Call] to transmt the selected TX code. USING [TX CODE CH UP]/[TX CODE CH DOWN] KEY: If the transcever has a [TX Code CH Up] or [TX Code CH Down] key assgnment, the programmed TX code channel can be selected drectly when pushed. 9 2 BASIC OPERATION USING [TX CODE ENTER] KEY: q Push [TX Code Enter] to enter the TX code edt mode. · The dgt to be edted blnks. D TX code number edit (PMR operaton only) If the transcever has [TX Code CH Select] or [TX Code Enter] assgned to t, TX code contents can be edted wthn the allowable dgts. USING [TX CODE CH SELECT] KEY: q Push [TX Code CH Select] to enter the TX code channel selecton mode. · Select the desred operatng channel before enterng the TX code channel selecton mode f necessary. w Push [TX Code Enter] to select the desred dgt to be edted. e Push [CH Up] or [CH Down] to select the desred dgt. The dgt to the rght wll blnk automatcally. t Repeat e and r to edt all allowable dgts. y After edtng, push [TX Code Enter] to set. · Return to the stand-by mode. w Push [TX Code CH Select] for 1 sec. to enter the TX code edt mode. · The dgt to be edted blnks. u Push [Call] to transmt. e Push [TX Code CH Select] to select the desred dgt to be edted. r Push [CH Up] or [CH Down] to select the desred dgt. [. . . ] NEVER remove the fuse-holder from the DC power cable. Red Black t r r O. TIONAL CABLE (O. C-1. 939) Connect an external modem, dmmer control, etc. t DC . OWER RECE. TACLE Connects to a 12 V DC battery. Ths could damage the transcever. 1. 2V Battery 14 NOTE: Use the termnals as shown below for the cable connectons. [. . . ]