User manual ICOM IC-2000-H

[. . . ] This may pose a fire hazard or result in an electric shock. RWARNING!NEVER operate the transceiver while driving a vehicle. Safe driving requires your full attention-- anything less may result in an accident. EXPLICIT DEFINITIONS The explicit definitions below apply to this instruction manual. DEFINITION Personal injury, fire hazard or electric shock RWARNING may occur. [. . . ] · Cancel the DTMF memory encoder function in advance. 48) Rotate the tuning dial to select and set the desired frequency. NOTE: The subaudible tone frequency can be set in a memory channel temporarily. However, the set contents are cleared once the memory/call mode is selected. To store the tone frequency permanently, overwrite the channel information. É Push [Y] or [Z] to select and set the desired frequency. · Pushing and holding [Y] or [Z] changes the frequency continuously. Ñ Push [ECLR] to exit set mode. · Subaudible tone frequency list 67. 0 69. 3 71. 9 74. 4 77. 0 79. 7 82. 5 85. 4 88. 5 91. 5 94. 8 97. 4 100. 0 103. 5 107. 2 110. 9 114. 8 118. 8 123. 0 127. 3 131. 8 136. 5 141. 3 146. 2 151. 4 156. 7 159. 8 162. 2 165. 5 167. 9 171. 3 173. 8 177. 3 179. 9 183. 5 186. 2 189. 9 192. 8 196. 6 199. 5 (unit: Hz) 203. 5 206. 5 210. 7 218. 1 225. 7 229. 1 233. 6 241. 8 250. 3 254. 1 26 5 REPEATER OPERATION I Offset frequency HI DUP 1 5 9 USING SET MODE The display shows that a 0. 6 MHz (600 kHz) frequency is set. Ä Push [BAND] to select the desired band, if necSET B essary. Å Set the mode/channel you wish to set the offset frequency to, such as VFO mode or memory/call channel. · The offset frequency can be independently programmed into each mode or channel. Separate setting for each band Push [BAND] to select the desired band. Select the mode/channel you wish to set the offset frequency to, such as VFO mode or memory/call channel. · The offset frequency can be independently programmed into each mode or channel. Ç Push [FSET] one or more times until "DUP" appears and flashes as shown at left. · Pushing [GENT] reverses the order of selection. · Cancel the DTMF memory encoder in advance. 48) Push [SET] one or more times until "DUP" appears and flashes as shown above. · Pushing [MONI] reverses the order of selection. · Cancel the DTMF memory encoder in advance. 48) É Push [Y] or [Z] to select and set the desired frequency. · Selectable step increment is the same as the preset tuning step. 18) · Pushing and holding [Y] or [Z] changes the frequency continuously. Rotate the tuning dial to set the desired frequency. · Selectable step increment is the same as the preset tuning step. Å Set the desired frequency in VFO mode: Push [VFO] to select VFO mode. offset frequency, duplex direction, subaudible tone encoder ON/OFF and its frequency), if required. Ñ Push [FUNC] then [EMW] for 1 sec. to program. 3 beeps may sound and the VFO contents (including the subaudible tone frequency, etc. ) are programmed. Memory channel number advances when continuing to push [MW] after programming. [EXAMPLE]: Programming 145. 870 MHz into memory channel 20 via the microphone. Push BAND , MONI VFO 1 8 HIGH 4 7 MID 5 MW ENT C DUP+ DUP Push FUNC then CLR A momentarily HI 1 5 9 HI 1 5 9 HI 1 M 5 9 MW Push Push FUNC then CLR A for 1 sec. and continue pushing 1 5 9 HI 1 M 5 9 HI HI 1 5 9 31 MEMORY OPERATION 6 I Transferring memory contents This function transfers a memory channel's contents into a VFO (or another memory/call channel). This is useful when searching for signals around a memory channel frequency and for recalling the offset frequency, subaudible tone frequency, etc. Push DUP HI T 1 M Ä Push [BAND] to select the desired band, if necMW essary. Å Select the memory channel to be transferred: Push [MR] to select memory mode. Push [Y] or [Z] to select the memory channel; or push [GENT] then push the desired memory channel number (2 digits) to select the memory channel directly. MW S. MW for 1 sec. T 1 5 9 Ç Push [FUNC] then [EMW] momentarily, then push [Y] or [Z] to select another memory channel to transfer. · To transfer to the VFO, push [FUNC] then push and hold [EMW] instead of pushing momentarily. 5 9 DUP HI MW FUNC + CLR A É Push [FUNC] then [EMW] for 1 sec. to transfer when a momentary push was used in the previous step. Push [BAND] one or more times to select a band. Select the memory channel to be transferred: Push [S. MW] momentarily, then rotate the tuning dial to select another memory channel to transfer. Select memory mode by pushing [M/CALL] once or twice ("!" appears). Rotate the tuning dial to select the memory channel. · To transfer to the VFO, push and hold [(S. MW)MW] instead of pushing momentarily. Push and hold [(S. MW)MW] to transfer when a momentary push was used in the previous step. 32 6 MEMORY OPERATION I Memory clearing Contents of programmed memories can be cleared (blanked), if desired. Push [S. MW] momentarily. [. . . ] Adjustable angle and direction for optimum installation positioning. OPC-440/647 MIC EXTENSION CABLE Cable length OPC-440: 5. 0 m; 16. 4 ft OPC-647: 2. 5 m; 8. 2 ft. OPC-347 DC POWER CABLE Has a 20 A capacity and a length of 7. 0 m (23. 0 ft). OPC-441 SPEAKER EXTENSION CABLE Cable length: 5. 0 m; 16. 4 ft. Some of the following options may not be available due to variations in local electrical standards, etc. [. . . ]