User manual ICOM IC-2100-T SERVICE MANUAL

[. . . ] · American National Standards Institute (C95. 1­1992), IEEE Standard for Safety Levels with Respect to Human Exposure to Radio Frequency Electromagnetic Fields, 3 kHz to 300 GHz. · American National Standards Institute (C95. 3­1992), IEEE Recommended Practice for the Measurement of Potentially Hazardous Electromagnetic Fields-- RF and Microwave. C AU TIO N To ensure that your exposure to RF electromagnetic energy is within the FCC allowable limits for occupational use, always adhere to the following guidelines: · DO NOT operate the radio without a proper antenna attached, as this may damage the radio and may also cause you to exceed FCC RF exposure limits. A proper antenna is the antenna supplied with i this radio by the manufacturer or an antenna specifically authorized by the manufacturer for use with this radio. · DO NOT transmit for more than 50% of total radio use time ("50% duty cycle"). [. . . ] Check the vehicle battery voltage in this case. If the charge indicator flashes red, there may be a problem with the battery pack (or charger). Re-insert the battery pack or contact your dealer. Check orientation for correct charging. (Insert together with charging adapter. ) BC-119N + AD-101 AD-99-- Use Spacer A only!Therefore, charging the battery in intervals, and not for extended periods is recommended. D Battery pack life When the operating period becomes extremely short, even after charging the battery pack fully, a new battery pack is needed. 9 3 BATTERY PACKS ` Battery case (Option) When using an optional BP-208 BATTERY CASE attached to the transceiver, install 6 AA (R6) size alkaline batteries as illustrated below. D CAUTION · Use ALKALINE batteries only. · Make sure all battery cells are the same brand, type and capacity. · Never mix old and new batteries. Either of the above may cause a fire hazard or damage the transceiver if ignored. · Never incinerate used battery cells since internal battery gas may cause them to rupture. · Never expose a detached battery case to water. w Push the [DTMF Autodial] switch to send a DTMF code. D DTMF RE-DIAL FUNCTION This function allows you to transmit the last-used DTMF code at the push of a key. Push the [Re-dial] switch momentarily to activate the function. · The previously transmitted DTMF code is automatically transmitted. · If no code has been transmitted since turning the power ON, this function does not activate. D EMERGENCY FUNCTION The emergency function allows you to send an emergency signal quickly and easily to your Base Station, etc. Push and hold the [Emergency Single/Repeat] switch for 1 sec. to activate the emergency function. · The transceiver selects a pre-programmed channel, then sends an emergency signal to your Base Station. · The pre-programmed channel remains selected until a control signal is received from the Base Station, or power is turned OFF. · The emergency call is repeatedly transmitted at pre-programmed intervals. 14 PROGRAMMABLE FUNCTIONS 4 D DISPLAY LIGHTING The function display has 3 backlight conditions. AUTO : When any key, except [PTT], is pushed, the backlight turns ON for 5 sec. D SmarTrunk IITM functions This transceiver provides SmarTrunk IITM functions. (Optional UT-105 SmarTrunk II TM Logic Board is required. ) The optional UT-105 allows communication over conventional channels or SmarTrunk IITM channels. Select a channel bank for SmarTrunk IITM before trunking operation. [. . . ] Otherwise the unit will not work correctly. (Other optional units can be plugged into either slot. ) Slot 2 Slot 1 y Program the necessary information with the cloning software before operation. Please ask your dealer or system operator for details. 23 9 OPTIONS D BATTERY PACKS/CASE · BP-208 BATTERY CASE Allows a set of Alkaline batteries to operate the handheld when charging rechargeable batteries or in emergencies, etc. · BP-209 Ni-Cd BATTERY PACK 7. 2 V/1100 mAh Ni-Cd battery pack, allows more than 7 hours operation. [. . . ]