User manual ICOM IC-229A-E-H

[. . . ] NEVER operate the transceiver while driving a vehicle. Safe driving requires your full attention--anything less may result in an accident. NEVER disassemble the remote controller. NEVER connect the transceiver to a power source of more than 16 V DC or using reverse polarity. [. . . ] Repeat r through i to set the desired name. !0 Push [ï] again to exit the edit screen. MAIN EDIT MAIN ICOM2800 Y Z EDIT 1 2 3 . 0 SKIP 88. 5 0. 6000 MW 145. 320 TON M I D - L O DUP 12 MAIN EDIT TON DUP To display the programmed memory name, turn the memory name indication ON in set mode. 67) r Push [EDIT] to enter programming mode. · The first character of the name flashes. 37 7 MEMORY/CALL CHANNELS D Programming a call channel q Select VFO mode with the desired band's [V/MH]. · Push [CHG/L] if [V/MH] is not displayed. s Call channel 1 call channel is available for each band to store a mostoften-used frequency for quick recall. D Selecting a call channel q Push [M/C] to select a call channel. · Push [CHG/L] if [M/C] is not displayed. · "C" appears when call channel is selected. MAIN SCP V/MH TS MAIN 14 6. 010 MAIN SCP MID-LO C V/MH TS w Set the desired frequency: ¯ Set the frequency using the desired band's tuning dial. offset frequency, duplex direction, subaudible tone frequency, etc. ), if required. e Push the desired band's [S. MW] momentarily to indicate memory channels. · Push [CHG/L] if [S. MW] is not displayed. · Do not hold [S. MW] for more than 0. 5 sec. , otherwise the memory channel will overwrite the selected memory channel. w Push [V/MH] to select VFO mode, if desired. to select the selected band's call channel. r Rotate the tuning dial to select the call channel. · "C" appears when a call channel is selected. t Push [(S. MW)MW] for 2 sec. to program. CALL [EXAMPLE]: Programming a call channel. MAIN S. MW MW MAIN EDIT MAIN EDIT DUP 146. 200 TON MID-LO momentarily MAIN EDIT DUP 1 TON DUP 146. 010 TON MID-LO MAIN MAIN EDIT MAIN EDIT DUP M 1 TON DUP 146. 010 TON MID-LO MAIN S. MW MW MAIN EDIT for 2 sec. MAIN EDIT TON DUP MAIN M C TON DUP 14 6. 200 MAIN EDIT MID-LO 1 TON DUP call channel 38 MEMORY/CALL CHANNELS D Programming a call channel via the microphone MW A 7 D Transferring call channel contents The call channels can be transferred in a similar manner to memory channel transferring. q Select call channel with the desired band's [M/C]. · Push [CHG/L] if [M/C] is not displayed. · "C" appears when the call channel is selected. t Push [Y] or [Z] to select the desired channel. · Call channel (C), VFO (- -) and scan edges (1A ­ 3B), as well as regular memory channels, can be transferred in this way. w Rotate the desired band's tuning dial to select the desired scratch pad memory. · One of "L1" to "L5" or "R1" to "R5" appears. y Push [FUNC] then [E MW] for 2 sec. to transfer. e Push the desired band's [S. MW] momentarily to indicate memory channels. · Push [S. MW] for 2 sec. to transfer the scratch pad memory to VFO. 41 9 SCAN OPERATION A tone scan function is available to search for subaudible tones (e. g. when you want to find a subaudible tone frequency necessary to open a repeater). 53 for details. s Scan types Scanning searches for signals automatically and makes it easier to locate new stations for contact or listening purposes. There are 3 scan types and 4 resume conditions to suit your operating needs. 43) Repeatedly scans all frequencies over the entire band. Used as the simplest scan without any preliminary settings necessary. PROGRAMMED SCAN (p. 43) Band edge Scan edges Band edge Band edge Scan Jump Band edge Scan Jump Repeatedly scans between two user-programmed frequencies. Used for checking for frequencies within a specified range such as repeater output frequencies, etc. 3 pairs of scan edges are available. MEMORY SCAN (p. [. . . ] · Correct the subaudible tone frequency. · The frequency lock function is activated. · Priority watch is paused on the watching fre- · Push [(PRO) PRIO] or [(MEM) PRIO] to resume quency. · Set the squelch to the threshold point. [. . . ]