User manual ICOM IC-2340H-A-E

[. . . ] We want to take a couple of moments of your time to thank you for making your IC-2340H-A-E your radio of choice, and hope you agree with Icom's philosophy of "technology first. " Many hours of research and development went into the design of your IC-2340H-A-E. IMPORTANT READ ALL INSTRUCTIONS carefully and completely before using the transceiver. SAVE THIS INSTRUCTION MANUAL-- This instruction manual contains important operating instructions for the IC-2340H-A-E. EXPLICIT DEFINITIONS DEFINITION Personal injury, fire hazard or electric shock R WARNING!CAUTION NOTE Equipment damage may occur. No risk of personal injury, fire or electric shock. WORD D FEATURES 65 W* of high transmit output power (except Korea/Taiwan versions) Tone squelch, DTCS squelch standard Dual color (amber & green) LCD backlight Remote control microphone available (optional for some versions) Optional Digital modulator/demodulator Optional DTMF decoder Icom, Icom Inc. [. . . ] Used for checking for frequencies within a specified range such as repeater output frequencies, etc. 3 pairs of scan edges are available. MEMORY SCAN (p. 38) SKIP M1 M0 M 199 M6 M5 M2 M3 M4 SKIP Repeatedly scans memory channels except those set as skip channels. Used for oftencalled channels and for bypassing normally busy channels such as repeater frequencies. SCAN RESUME CONDITION (p. 42) Receiving a signal Pause scan 2 sec. Timer scan Pausing 4 resume conditions are available: 3 timer scans and pause scan. When receiving a signal, pause scan pauses until the signal disappears; timer scans pause for 5, 10 or 15 sec. NOTE: A tone scan function is available to search for subaudible tones (e. g. when you want to find a subaudible tone frequency necessary to open a repeater). 37 SCAN OPERATION 7 I Scan start/stop D Preparation Scan resume condition (p. 39, 40); program 2 or more memory channels (pgs. 25, 26); set skip settings, if desired (p. v Push [FUNC], then push [CLR A(MW)] for 1 sec. to program. · 3 beeps sound and VFO is automatically selected. · Memory channel number advances to the next scan edge channel, 1b, 2b or 3b, when continuing to push [CLR A(MW)] after programming. b To program a frequency for the other scan edge channels, repeat steps z to v. 7 [EXAMPLE]: Programming 145. 800 MHz into scan edges 1b. Push DIGITAL PRIO AO BUSY MUTE NAR MID LOW LOCK ANM DUP T-SCAN PRIO SCAN Push DIGITAL PRIO AO BUSY MUTE NAR MID LOW LOCK ANM DUP T-SCAN PRIO SCAN Push MUTE NAR MID LOW LOCK then momentarily. DIGITAL PRIO AO BUSY ANM DUP T-SCAN PRIO SCAN SET MONI LOW TONE M/CALL V/ MHz SET MONI LOW TONE M/CALL V/ MHz SET MONI LOW TONE M/CALL V/ MHz Push DIGITAL PRIO AO BUSY MUTE NAR MID LOW LOCK ANM DUP T-SCAN PRIO SCAN Push then 1 sec. and continue to push MUTE NAR MID LOW LOCK ANM DUP T-SCAN PRIO SCAN DIGITAL PRIO AO BUSY SET MONI LOW TONE M/CALL V/ MHz SET MONI LOW TONE M/CALL V/ MHz " "Beep " Beep " Beep " DIGITAL PRIO AO BUSY MUTE NAR MID LOW LOCK ANM DUP T-SCAN PRIO SCAN SET MONI LOW TONE M/CALL V/ MHz 40 7 SCAN OPERATION I Skip channel setting The memory skip function speeds up scanning by checking only those memory channels not set as skip channels. Set skip channels as follows. DIGITAL PRIO AO BUSY MUTE NAR MID LOW LOCK ANM DUP T-SCAN PRIO SCAN USING SET MODE SET B The display shows that memory channel 15 is set as a skip channel. SET MONI LOW TONE M/CALL V/ MHz z Select a memory channel. Select memory mode by pushing [MR/CALL]. Y Z Push [Y] or [Z] to select the desired channel to be a skip channel. x Push [SET B(D-OFF)] to enter set mode. c Push [SET B(D-OFF)] or [ENT C(T-OFF)] several times until "CHS" appears as shown at left. Y Z v Push [Y] or [Z] to set or cancel the skip setting. · See item r at left for skip indicator details. b Push [CLR A(MW)] to exit set mode. q Select a memory channel: Push [M/CALL PRIO ] to select memory mode. [. . . ] Japan 1-1-32, Kamiminami, Hirano-ku Osaka 547-0003, Japan Declare on our sole responsibility that this equipment complies with the essential requirements of the Radio and Telecommunications Terminal Equipment Directive, 1999/5/EC, and that any applicable Essential Test Suite measurements have been performed. Kind of equipment: Type-designation: FM TRANSCEIVER Düsseldorf 8th Dec. 2003 Place and date of issue Icom (Europe) GmbH Himmelgeister straße 100 D-40225 Düsseldorf Authorized representative name i2200H Version (where applicable): This compliance is based on conformity with the following harmonised standards, specifications or documents: i) ii) iii) iv) EN 301 489-1 v 1. 3. 1 (2001-09) EN 301 489-15 v 1. 1. 1 (2000-09) EN 301 783 v 1. 1. 1 (2000-09) EN 60950 (1992-08) + A11:1997 T. Maebayashi General Manager 15 16 Signature 92 17 MODE ARRANGEMENT VFO mode (p. [. . . ]