User manual ICOM IC-24ET

[. . . ] If you experience a ringing in your ears, reduce the volume level or discontinue use. AVOID using or placing the receiver in direct sunlight or in SAVE THIS INSTRUCTION MANUAL -- This instruction manual contains important operating instructions for the IC-24ET. EXPLICIT DEFINITIONS The explicit definitions below apply to this instruction manual. WORD R WARNING CAUTION NOTE DEFINITION Personal injury, fire hazard or electric shock may occur. No risk of personal injury, fire or electric shock. areas with temperatures below ­10°C (+14°F) or above +60°C (+140°F). [. . . ] · Non-programmed channels cannot be selected. s Transferring memory contents to another memory q Select memory mode with [V/M]. w Select the memory channel to transfer with [DIAL]. · Rotate [DIAL] while pushing [FUNC] to select a memory bank or programmed scan edge channel. e Push [V/M] to select VFO mode. r Set the desired frequency: ¯ Select the desired band with [BAND]. offset frequency, duplex direction, tone squelch frequency, etc. ), if required. to program the selected channel. · Keep pushing for 2 sec. or more to automatically select the next memory channel, if desired. e Push [FUNC] + [(V/M)MW] momentarily to indicate memory channels. · Do not hold [FUNC] + [(V/M) MW] for more than 0. 5 sec. , otherwise the memory channel contents will be transferred to VFO. r Rotate [DIAL] to select the channel to transfer to. · Rotate [DIAL] while pushing [FUNC] to select a memory bank or programmed scan edge channel. · VFO (VF), as well as regular memory channels, can be transferred in this way. t Push [FUNC] + [(V/M)MW] for 2 sec. to transfer. [EXAMPLE]: Transferring memory channel 3 (memory bank 0) to 20 (memory bank 0). FUNC FUNC + V/M MW V/M MW + V/M MW FM FM FM momentarily Select memory channel MR MR MR for 1 sec. MR blank channel 13 5 MEMORY CHANNELS s Memory bank selection The receiver has 400 memory channels in 8 banks for storage of often-used frequencies. w Rotate [DIAL] while pushing [FUNC] to select the desired memory banks. · "1" ­ "3" indicate memory banks 1 to 3; "" indicates memory bank 4; "1" ­ "3" indicate memory banks 5 to 7; no bank indicator indicates memory bank 0. s Memory clear Unwanted memory channels can be cleared (erased). Before clearing a memory channel make sure it is no longer needed as cleared memories cannot be recalled. w Set the memory channel to be cleared with [DIAL]. · Rotate [DIAL] while pushing [FUNC] to select a memory bank or programmed scan edge channel. e Rotate [DIAL] to select the desired memory channel. FM FM FM e Select VFO mode with [V/M] and push [FUNC] + [(V/M)MW] momentarily to indicate the selected memory channel. · Do not hold [FUNC] + [(V/M) MW] for more than 0. 5 sec. , otherwise the selected memory channel will be overwritten. MR MR MR 3 r Push [FUNC] + [(MODE) LOCK] for 2 sec. · "P SKIP" flashes when the frequency skip function is turned ON. 19) · "0P"­"24P" flash to indicate which pair of scan edges is being scanned. · To change the scanning direction, rotate [DIAL]. · If the pocket beep function is activated, the receiver automatically selects the tone squelch function when a scan starts. e Turn the memory bank scan ON or OFF in the memory scan set mode, if desired. · See below for details. r Push [FUNC] + [Y] or [Z] momentarily to start the memory (bank) scan. · Decimal point flashes while scanning. · To change the scanning direction, rotate [DIAL]. · If the pocket beep function is activated, the receiver automatically selects the tone squelch function when a scan starts. t To stop the scan, push [FUNC] + [Y] or [Z] again. D Memory bank selection q Select memory mode with [V/M]. w While pushing [FUNC], push [BAND] to enter memory scan set mode. e Rotate [DIAL] to select the memory bank scan ON or OFF. · "ALL" indicates all memory banks are scanned (memory bank scan OFF); "BANK" indicates memory bank scan is turned ON. t To stop the scan, push [FUNC] + [Y] or [Z] again. If the same frequencies are programmed into a pair of scan edges, programmed scan does not start. For programmed scan, scan edges must be programmed in advance. Program scan edges in the same manner of programming a memory channel and select a scan edge. [. . . ] · Turn the channel indication mode OFF in set mode. · Turn beep tones ON in set mode. · Select a suitable operating mode in set mode. No sound comes from the speaker. Frequency cannot be set. No beeps sound. [. . . ]