User manual ICOM IC-275H

[. . . ] LTR® is a registered trademark of the E. F. Johnson Company. All other products or brands are registered trademarks or trademarks of their respective holders. i TABLE OF CONTENTS DO NOT use or place the transceiver in areas with temperatures below ­22°F (­30°C) or above +140°F (+60°C) or, in areas subject to direct sunlight, such as the dashboard. IMPORTANT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . i EXPLICIT DEFINITIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] 8 I Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 3 SAFETY TRAINING INFORMATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 AVOID operating the transceiver without running the vehicle's engine. The vehicle's battery will quickly run out if the transceiver transmits while the vehicle's engine OFF. AVOID placing the transceiver in excessively dusty environments. AVOID placing the transceiver against walls. This will obstruct heat dissipation. AVOID the use of chemical agents such as benzine or alcohol when cleaning, as they damage the transceiver surfaces. BE CAREFUL!The transceiver will become hot when operating continuously for long periods. only CAUTION: Changes or modifications to this transceiver, not expressly approved by Icom Inc. , could void your authority to operate this transceiver under FCC regulations. ii 1 q PANEL DESCRIPTION I Front panel w e r t DEALER-PROGRAMMABLE KEYS [P0] to [P4] Desired functions can be programmed independently by your dealer. y POWER SWITCH [POWER] Push to turn the power ON and OFF. · At power ON, a power-up alert tone sounds for about 1 sec. And the transceiver automatically starts scanning if the scan function had been activated before the power was turned OFF. u y t q AF VOLUME CONTROL KNOB Rotate the knob to adjust the audio output level. · Minimum audio level is pre-programmed. w LEFT UP/DOWN []/[] KEYS Push to select the talk group on the LTR or PassPort system. e FUNCTION DISPLAY Displays a variety of information, such as an operating channel text, talk group text. 2 (15 A: IC-275H/F620, 20 A: IC-F621) q Microphone . . . . . . . . . . . . . . . . . . . . . . 1 w Microphone hanger and screw set . . . . . . . . . . . . . . . . . . . . . 1 (OPC-345 : IC-275H/F620, OPC-1132: IC-F621) t Mounting bracket . . . . . . . . . . . . . . 4 !3 Function name stickers* (1705 LCD SEAL(H)) . . . . . . . . . . . . . . . . 1 *Function name stickers There are no names on the programmable function keys since the needed functions can be assigned to these keys. Attach the supplied function name stickers above the appropriate keys. 4 2 CONNECTION AND MAINTENANCE I Mounting the transceiver The front panel can be inverted for correct viewing while leaving the built-in speaker facing away from the mounting surface. D Inverting the front panel q Unscrew the 2-side screws. w Detach the front panel forward from the transceiver. e Bend the flat cable between front panel and main unit as shown in the following diagram. r Invert the transceiver 180 degrees clockwise as below. t Re-attach the front panel to the transceiver. y Tighten the 2 screws. CAUTION: Flat cable orientation normal bend line inverted bend line to main unit to front panel · NEVER rotate the transceiver more than 180 degrees. · DO NOT bend the flat cable too hard. [. . . ] This radio is designed for and classified as "Occupational Use Only", meaning it must be used only during the course of employW ARN ING ment by individuals aware of the hazards, and the ways to minimize such hazards. This radio is NOT intended for use by the "General Population" in an uncontrolled environment. · For compliance with FCC and Industry Canada RF Exposure Requirements, the transmitter antenna installation shall comply with the following two conditions: 1. The transmitter antenna gain shall not exceed 0 dBi. [. . . ]