User manual ICOM IC-2GE

[. . . ] (5 to 10 cm) away from the lips and the transceiver is vertical. SAVE THIS INSTRUCTION MANUAL -- This instruction manual contains important operating instructions for the IC-F3021T/S, IC-F3023T/S, IC-F3026T/S VHF TRANSCEIVERS and the IC-F4021T/S, IC-F4023T/S, ICF4026T/S UHF TRANSCEIVERS. R CAUTION!NEVER operate the transceiver with a headset or other audio accessories at high volume levels. NEVER short the terminals of the battery pack. EXPLICIT DEFINITIONS DEFINITION Personal injury, fire hazard or electric shock RWARNING may occur. CAUTION NOTE Equipment damage may occur. [. . . ] USER SET MODE KEY Push and hold for 1 sec. to enter user set mode. · During user set mode, push this key to select an item, and change the value or condition using [CH Up]/[CH Down]. EMERGENCY KEY Push and hold for a specified period to transmit an emergency call. · If you want to cancel the emergency call, push (or push and hold) the key again before transmitting the call. · The emergency call is transmitted one time only or repeatedly until receiving a control code depending on the pre-setting. Push and hold this key for 1 sec. User set mode is also available via the `Power ON function. ' Refer to (p. OPT OUT KEYS Push to control the output signal level of the optional ports in the optional unit connector. OPT MOMENTARY KEYS Controls the output signal level of the optional ports in the optional unit connector while pushing and holding this key. SURVEILLANCE KEY Push to turn the surveillance function ON or OFF. When this function is turned ON, the beep is not emitted and the LCD backlight does not light when a signal is received or a key is pushed, etc. TX CODE CHANNEL SELECT KEY Push to enter the ID code channel selection mode directly. Then set the desired channel using [CH Up]/[CH Down]. The tone signaling employed may be a selective calling system which allows you to call specific station(s) only and prevent unwanted stations from contacting you. q Select the desired TX code channel or 2-tone code according to your System Operator's instructions. · This may not be necessary depending on programming. Entering the user set mode: q While pushing and holding [Side2] and [Side3], rotate [VOL] to turn the power ON. w Push [P0] several times to select the appropriate item. Then push [CH Up] or [CH Down] to set the desired level/condition. · Available set mode functions are Backlight, Beep, Beep Level, SQL Level, Mic Gain, Battery Voltage and Signal Moni. I Emergency transmission When [Emergency Single] or [Emergency Repeat] is pushed, an emergency signal is automatically transmitted for the specified time period. When [Emergency] is pushed, the DTMF emergency signal is transmitted on the priority channel. When [Emergency Single] or [Emergency Repeat] is pushed for the specified time period, the DTMF emergency signal is transmitted once or repeatedly on the emergency channel. However, when no emergency channel is specified, the signal is transmitted on the previously selected channel. e Rotate [VOL] to turn the power OFF to exit user set mode. NOTE: User set mode is also available via a programmable function key. Refer to "USER SET MODE KEY. " (p. 9) I Scrambler function The voice scrambler function provides private communication between stations. The frequency inversion type is equipped to all versions, moreover, the optional Rolling or Non-rolling type can be available. q Push [Scrambler] to turn the scrambler function ON. ·" " appears. w Push [Scrambler] again to turn the scrambler function OFF. ·" " disappears. 14 BASIC OPERATION 3 I Stun function When the specified ID, set as a killer ID, is received, the stun function is activated. [. . . ] An AC adapter should be purchased separately. ·BC-160 DESKTOP CHARGER + BC-145 AC ADAPTER For rapid charging of battery packs. An AC adapter is supplied with the charger depending on versions. 24 D DC CABLES · CP-17L CIGARETTE LIGHTER CABLE Allows charging of the battery pack through a 12 V cigarette lighter socket. [. . . ]