User manual ICOM IC-2KL

[. . . ] CAUTION NOTE Equipment damage may occur. No risk of personal injury, fire or electric shock. WORD D FEATURES V/V, U/U simultaneous receive capability Independent controls for each left and right bands Separate controller for flexible installation 50 W* of high transmit output power *VHF band; 35 W for UHF Remote control microphone standard New DMS (Dynamic Memory Scan) system i Icom, Icom Inc. and the logo are registered trademarks of Icom Incorporated (Japan) in the United States, the United Kingdom, Germany, France, Spain, Russia and/or other countries. PRECAUTION RWARNING RF EXPOSURE! [. . . ] rPush [SET· ] or [LOW·PRIO] until "DUP" and offset frequency appear. MAIN TX DUP Push M b Push [Y] or [Z] to set the desired offset. M · Direct frequency entry from the keypad is not possible. [LOW·PRIO] [SET· ] "DUP" and offset frequency appear n Push [CLR A(MW)] to exit set mode. NOTE: The offset frequency can be set in a memory/call channel temporarily. However, the set frequency is cleared once another memory channel or VFO mode is selected. To store the offset frequency permanently, overwrite the channel information. tRotate the main band's [DIAL] to set the desired offset frequency. y Push [TONE·DTMF] to exit set mode. 27 MEMORY OPERATION I General description The transceiver has 212 memory channels including 10 scan edge memory channels (5 pairs), and 2 call channels. Each of these channels can be individually programmed with operating frequency (pgs. 27), subaudible tone encoder or tone squelch and its tone frequency (pgs. 23, 25, 51, 52) and skip information* (p. In addition, a total of 10 memory banks, A to J, are available for usage by group, etc. *except for scan edge memory channels. 5 4 5 D Using the [Y]/[Z] keys MR/CALL Y/Z z Push [BAND] to select the desired band as the main band. c Push [Y] or [Z] to select and set the desired memory channel. · Pushing [Y]/[Z] for 1 sec. Push the desired band's [M/CALL·MW] several times to select memory mode or call channel, then rotate the same band's [DIAL] to select the desired memory or call channel. to transfer the selected memory/call channel contents to the VFO. · VFO mode is selected automatically. MR/CALL MW [Y]/[Z] z Push [BAND] to select the desired band as the main band, if necessary. x Select the memory/call channel to be transferred. Push [MR/CALL] to select memory mode, then select the desired memory channel via [Y]/[Z] or keypad. then push [Y]/[Z] to select the call channel. c Push [FUNC], then [CLR A(MW)] for 1 sec. to transfer the selected memory/call channel contents to the VFO. · VFO mode is selected automatically. [EXAMPLE]: Transferring memory channel 30 contents to VFO. Front panel operation: Push M/CALL to select memory mode. Rotate MW MAIN TX for selecting memory channel. MAIN TX DUP T Push M/CALL MW for 1 sec. MAIN TX DUP T M M M HM-133 operation: Push to select memory mode. Select memory channel. Push then push for 1 sec. 31 MEMORY OPERATION D Memory/callcall/memory q Select the memory/call channel to be transferred. Push the desired band's [M/CALL·MW] several times to select memory mode or call channel, then rotate the same band's [DIAL] to select the desired memory or call channel. w Push the same band's [M/CALL·MW] for 1 sec. · "!" indicator and "­ ­" indication blink, and shows VFO conditions. 5 MR/CALL MW [Y]/[Z] z Select the memory/call channel to be transferred. Push [MR/CALL] to select memory mode, then select the desired memory channel via [Y]/[Z] or keypad. [. . . ] audio 1. 8 A · Antenna connector : SO-239 (50 ) · Dimensions (proj. not included) : Main Unit 140(W) × 40(H) × 187(D) mm Remote controller 140(W) × 50(H) × 24. 5(D) mm : · Weight (approx. ) Main unit 1. 25 kg (incl. separation cable) Remote controller 150 g · Frequency coverage Europe Italy : D RECEIVER · Receive system : Double-conversion superheterodyne · Intermediate frequencies : Left band 1st: 38. 85 MHz, 2nd: 450 kHz Right band 1st: 46. 05 MHz, 2nd: 455 kHz · Sensitivity (FM: at 12 dB SINAD/AM: at 10 dB S/N): 144 MHz band Less than 0. 18 µV/0. 45 µV typ. 430 MHz band Less than 0. 18 µV/-- · Squelch sensitivity (threshold) : Less than 0. 13 µV · Selectivity (typical) : Wide More than 12 kHz/6 dB Less than 30 kHz/60 dB Narrow More than 6 kHz/6 dB Less than 20 kHz/60 dB · Spurious and image rejection : More than 60 dB · AF output power (at 13. 8 V DC) : More than 2. 4 W at 10% distortion with · Ext. [. . . ]