User manual ICOM IC-3200A-E

[. . . ] NEVER short the terminals of the battery pack. EXPLICIT DEFINITIONS DEFINITION Personal injury, fire hazard or electric shock RWARNING may occur. CAUTION NOTE Equipment damage may occur. No risk of personal injury, fire or electric shock. WORD DO NOT push PTT when not actually desiring to transmit. [. . . ] · Penalty timer Once the time-out timer is activated, transmission is further inhibited for a period determined by the penalty timer. 13 3 BASIC OPERATION D TX code number edit (PMR or BIIS PMR operation only) If the transceiver has [TX Code CH Select] or [TX Code Enter] assigned to it, TX code contents can be edited within the allowable digits. TO EDIT A TX CODE VIA [TX CODE CH SELECT] KEY: q Push [TX Code CH Select] to enter the TX code channel selection mode. · Select the desired channel using [UP] or [DOWN] if necessary. TO EDIT A TX CODE VIA [TX CODE ENTER] KEY: q Select the desired TX code channel via [TX Code CH Up] or [TX Code CH Down]. w Push [TX Code Enter] to enter the TX code edit mode. e Push [TX Code Enter] to select the desired digit to be edited. r Set the desired digit using [UP], [DOWN], [TX Code CH Up] or [TX Code CH Down] or 10-keypad*. *Depending on version. w Push [TX Code CH Select] for 1 sec. e Push [TX Code CH Select] to select the desired digit to be edited. r Set the desired digit using [UP], [DOWN], [TX Code CH Up], [TX Code CH Down] or 10-keypad. * *Depending on version. t Push [TX Code Enter] to set the digit. The editable digit will move to the right automatically. · When the 10-keypad is used to set, the editable digit will move to the right automatically without pushing [TX Code CH Select]. y Repeat r and t to input all allowable digits. u Push [Call] or [PTT] to transmit the edited TX code. t Push [TX Code CH Select] to set the digit. The editable digit will move to the right automatically. · When the 10-keypad is used to set, the editable digit will move to the right automatically without pushing [TX Code CH Select]. y Repeat r and t to input all allowable digits. u Push [Call] or [PTT] to transmit the edited TX code. 14 BASIC OPERATION D DTMF transmission If the transceiver has [DTMF Autodial] assigned to it, the automatic DTMF transmission function is available. " appears while receiving a signal. e Release [PTT] to return to receive. r To finish the conversation, push [MONITOR] (Moni(Audi)) to send the `Clear down' signal. · Either station can send a `Clear down' signal. ·" " is displayed for 2 sec. · " " disappears and the transceiver returns to the standby condition. 16 BIIS OPERATION 4 D Group call q When a group call is received; · Beeps sound. · " " appears and the mute is released. · The programmed text message (e. g. " ") and the calling station ID (or text) is displayed alternately, depending on the setting. · " " appears or blinks depending on the setting. D Displaying the received call record -- Queue indication The transceiver memorizes the calling station IDs for record. Up to 3 calls can be memorized, and the oldest call record is erased when a 4th call is received. However, once the transceiver is powered OFF, the all records are cleared. q Push [P1] (Digital) for 1 sec. · Displays following indication. When a record is available Appears Appears or blinks When no record is available w Push and hold [PTT], then speak into the microphone at a normal voice level. NOTE: Only one station is permitted to speak. ·" ·" " appears. [. . . ] · UT-109 (#02)/UT-110 (#02) SCRAMBLER UNITS Non-rolling type (UT-109)/Rolling type (UT-110) voice scrambler unit provides higher communication security. · UT-113 MAN DOWN UNIT Provides a measure of safety when working in a hazardous environment, etc. · UT-105 SmarTrunk IITM LOGIC BOARD Provides SmarTrunk IITM capabilities. · UT-117/117S* SmarTrunk 3GTM LOGIC BOARD Provides SmarTrunk 3GTM capabilities. [. . . ]