User manual ICOM IC-40S

[. . . ] TRANSCEIVER i40S FOREWORD READ ALL INSTRUCTIONS carefully and completely before using the transceiver. CAUTIONS R WARNING!NEVER hold the transceiver so that the antenna is very close to, or touching exposed parts of the body, especially the face or eyes, while transmitting. The transceiver will perform best if the microphone is 5 to 10 cm away from the lips and the transceiver is vertical. SAVE THIS INSTRUCTION MANUAL -- This instruction manual contains important operating instructions for the IC-40S. R WARNING!NEVER operate the transceiver with a headset or other audio accessories at high volume levels. [. . . ] [PTT] and the backlight function can be used while the lock function is in use. · If "T SQL" appears on the display, push [­] for 2 sec. twice to cancel the tone squelch function. r Release [PTT] to receive. t To cancel the duplex setting, push [DUP] on the desired channel. (Unit: Hz) 7 4 SCAN OPERATION s Open scan Open scan searches for transmitted signals automatically and makes it easier to locate new stations for contact or listening purposes. During open scan, transmission is not possible except on a busy channel. q Push [O/G] to select open scan. - "OS" appears when the open scan is selected. s Scan types The transceiver has 3 scan types with tag functions and 4 resume conditions providing scanning versatility. Tag channels are independently set for open, group and priority scans. Initially, all channels may be set as tag channels for all scans. OPEN SCAN X ch 40 ch 4 X ch 1 ch 2 X ch 3 w Push [SCN] to start open scan. - Cancelling tag channels speeds up the scan interval. 9) Start channel MR X ch 39 X ch 6 X ch 5 Repeatedly scans all tag channels in sequence. GROUP OR PRIORITY SCAN X ch 8 Scanning channel is displayed. Priority channel X ch 12 X ch 26 e When receiving a signal, scan pauses and resumes according to the selected scan resume condition. 10) r Push [SCN] to stop the scan. Repeatedly watches a priority channel while scanning only specified channels (tag channels). 8 SCAN OPERATION 4 s Group and priority scans Group and priority scans repeatedly watch a priority channel while scanning only specified channels. This is useful when waiting for calls on the priority channel or several specified channels. Group and priority scans behave differently when transmitting. During group scan, transmission is possible on a busy channel only. During priority scan, transmission is possible on a priority channel (or start channel) only. q Push [O/G] to select open scan. - "GS" or "PS" appears when the group or priority scan is selected, respectively. Start channel MR s Setting scan tag Scan tag must be set before starting scan. Tag channels are independently set for open, group and priority scan. w Push [O/G] to select the desired scan type. to set the channel as a tag channel. - "X" appears for tag channels. r Repeat step e to cancel the tag channel setting. Appears for channels to be scanned. MR SCN for 2 sec. w Select the priority channel if desired. - Push [Y] or [Z] key to select a channel. [. . . ] ch. ) : FM (16K0F3E) : 25 kHz : 9. 6 V DC nominal (authorized battery packs) : ­10°C to +60°C : ±5 ppm : at 5 W 1. 6 A at 1 W 0. 7 A standby 60 mA max. audio 250 mA power saved 13 mA : 50 (nominal) : 57(W) 140(H) 37(D) mm : 370 g · Output power · Modulation · Max. frequency deviation · Spurious emissions · Adjacent channel power · External mic. 5 W (at 9. 6 V DC) : Variable reactance frequency modulation : ±5 kHz : 70 dB typical : 70 dB typical : 3-conductor 2. 5 (d) mm/2 k D General · Frequency coverage · Mode · Tuning step increment · Acceptable power supply (negative ground) · Usable temp. [. . . ]