User manual ICOM IC-45A-E

[. . . ] Safe driving requires your full attention-- anything less may result in an accident. SAVE THIS INSTRUCTION MANUAL -- This instruction manual contains important operating instructions for the IC-45A-E UHF TRANSCEIVER. EXPLICIT DEFINITIONS DEFINITION Personal injury, fire hazard or electric shock RWARNING may occur. CAUTION NOTE Equipment damage may occur. No risk of personal injury, fire or electric shock. WORD NEVER connect the transceiver to a power source of more than 16 V DC. [. . . ] r Push [MONI] several times until "CT" appears. [MONI] CT appears t Push [ ]/[ ] to select the desired frequency. · When "OFF" is displayed, push [DUP] to enables the tone frequency selection, in advance. y Push [MONI] for 1 sec. to exit the individual setting, then push [O] for 1 sec. to exit Set mode. · The under bar indicator appears. 4) 15 GROUP MODE OPERATION To cancel the group mode operation: q While in Function mode, push [O] (Bank/Func) for 1 sec. to enter Set mode. · Push [O] (Bank/Func) for 1 sec. to enter the transceiver into Function mode. 5 What is CTCSS (Continuous Tone Coded Squelch System) GROUP MODE ?CTCSS (Continuous Tone Coded Squelch System) GROUP MODE allows communication with silent stand by. Only signals containing a specific CTCSS frequency can open the squelch. This conveniently eliminates unwanted audio and is useful in group activities or security related activities where unwanted output can be a problem. Note that CTCSS group mode is not private--anyone can receive your calls. The IC-45A-E is equipped with 51 CTCSS frequency for CTCSS GROUP MODE use. to enter the TX code channel selection mode. · Push [O] (Bank/Func) for 1 sec. to enter the transceiver into Function mode. · Push [ ]/[ ] to select the desired TX code channel, if desired. Push [MONI] 6 r Push [MONI] (Call) to transmit the code on the selected channel. Appears while transmitting Push [MONI] w Push [MONI] (Call) for 1 sec. again to enter the TX code edit mode. CONVENIENT!· The TX code channel name can be assigned to the all 32 TX code channel via the optional CS-400PRO CLONING SOFTWARE. The TX code channel name allows you to easy to select the channel, find the channel user, and so on. · The long tone function is useful and provides you to proper individual or group call even through a repeater, or when the calling station is in scanning operation. The long tone function can be activated in Set mode. 30) Push [MONI] for 1 sec. The first digit starts blinking e Push [MONI] (Call) to select the desired digit to be edited. · Editable digit blinks Push [MONI] 18 6 SELCALL OPERATION ]/[ Push [ r Push [ ] to set the desired code. ] or [ ] · Select "" when group code is set. o Push [MONI] (Call) to transmit the code on the selected channel. Appears while transmitting Push [MONI] t Push [MONI] (Call) to set the code and the editable digit move to right automatically. NOTE: The TX code editable digit can only be set/changed with the optional CS-400PRO CLONING SOFTWARE. Push [MONI] y Repeat step r and t to input all allowed digits. u Push [MONI] (Call) to set the TX code. Push [MONI] i Push [MONI] (Call) to return to Function mode. 19 SELCALL OPERATION 6 I When receiving a call D Receiving an individual call When receiving an individual call (default setting); - "PiRo" beeps sound repeatedly for 10 sec. - Transmits the answer back call with single tone for 2 sec. - The received ID code is displayed and memorised into the transceiver. [. . . ] e Install the unit as shown in the diagram below. r Replace the bottom cover and screws, then re-connect the DC power cable. I Optional UT-109 or UT-110 installation q Turn the power OFF, then disconnect the DC power cable. w Unscrew the 4 cover screws, then remove the bottom cover. e Cut the pattern on the PCB at the TX mic circuit (MIC) and RX AF circuit (DISC) as shown below. [. . . ]