User manual ICOM IC-718

Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets... DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!

Sponsored Links

If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Lastmanuals provides you a fast and easy access to the user manual ICOM IC-718. We hope that this ICOM IC-718 user guide will be useful to you.

Lastmanuals help download the user guide ICOM IC-718.


ICOM IC-718 : Download the complete user guide (3888 Ko)

You may also download the following manuals related to this product:

   ICOM IC-718 BROCHURE (231 ko)
   ICOM IC-718 INSTRUCTION MANUAL (3769 ko)

Manual abstract: user guide ICOM IC-718

Detailed instructions for use are in the User's Guide.

[. . . ] INSTRUCTION MANUAL HF ALL BAND TRANSCEIVER i718 This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. IMPORTANT READ THIS INSTRUCTION MANUAL CAREFULLY before attempting to operate the transceiver. EXPLICIT DEFINITIONS WORD R WARNING CAUTION NOTE DEFINITION Personal injury, fire hazard or electric shock may occur. No risk of personal injury, fire or electric shock. SAVE THIS INSTRUCTION MANUAL. This manual contains important safety and operating instructions for the IC-718. PRECAUTIONS R WARNING HIGH VOLTAGE! [. . . ] r Select "VOX Delay" in quick set mode. · Push [ UP]/[ DN] one or more times to select "VOX Delay" t While speaking into the microphone, adjust [VOX DELAY] as desired. y Select "ANTI-VOX" in quick set mode. · Push [ UP]/[ DN] one or more times to select "AN VOX" u If the receive audio from the speaker toggles the transceiver to transmit during receive, adjust the "ANTI-VOX" to the point where it has no effect. i Push [SET] to exit the quick set mode. 27 5 RECEIVE AND TRANSMIT ï Optional AT-180 AUTOMATIC ANTENNA TUNER operation The AT-180 automatic antenna tuner matches the IC718 to the connected antenna automatically. Once the tuner matches an antenna, the variable capacitor angles are memorized as a preset point for each frequency range (100 kHz steps). Therefore, when you change the frequency range, the variable capacitors are automatically preset to the memorized point. · MANUAL TUNING During SSB operation on HF bands at low voice levels, the AT-180 may not be tuned correctly. to start manual tuning. · CW mode is selected, a side tone is emitted, and " " blinks; then, the previous mode is selected. CAUTION: NEVER transmit with the tuner ON when no antenna is connected. This will be damage both the transceiver and the antenna tuner. DO NOT!Both turners will not be function correctly. Y Y TUNER OPERATION [TUNER] · Tuner type setting (p. 46) q Push [PWR] for 1 sec. r Rotate the main dial to select "18". · AT-180 AUTOMATIC ANTENNA TUNER is selected. NOTE: NEVER select "4" (AH-4 AUTOMATIC ANTENNA TUNER), otherwise the transceiver trans- Push and hold 1 sec. to start manual tuning. If the tuner cannot reduce the SWR to less than 1. 5:1 after 20 sec. In this case, check the following: · the antenna connection and feedline · the antenna SWR (p. u Push [PWR] to turn power ON again. · AUTO TUNE: Push [TUNER] to turn the tuner ON. The antenna is tuned automatically during transmission when the antenna SWR is higher than 1. 5:1. · When the tuner is OFF, " " goes out. · Through inhibit The AT-180 has a through inhibit condition. When selecting this condition, the tuner can be used at poor SWR's. In this case, automatic tuning in the HF bands activates only when exceeding SWR 3:1. Therefore, manual tuning is necessary each time you change the frequency. Although termed "through inhibit, " the tuner will be "through" if the SWR is higher than 3:1 after tuning. CONVENIENT · Tuner sensitive condition If you require critical tuning at any time during transmission, select the tuner sensitive condition. · Automatic tuner start If you want to turn OFF the tuner under conditions of VSWR 1. 5:1 or less, use "automatic tuner on" and turn the tuner OFF. 46 for turning the function ON and OFF. Y [TUNER] Tuning indicator; 28 Y RECEIVE AND TRANSMIT 5 ï Optional AH-4 AUTOMATIC ANTENNA TUNER operation The AH-4 matches the IC-718 to a long wire antenna more than 7 m/23 ft long (3. 5 MHz and above). · See the AH-4 instruction manual for AH-4 installation and antenna connection details. [. . . ] The Icom Communications Interface-V (CI-V) controls the following functions of the transceiver. Up to 4 Icom CI-V transceivers or receivers can be connected to a personal computer equipped with an RS-232C port. 32 for setting the CI-V condition using set mode. IC-718 9­15 V DC BC-25 (optional) 13 ct- 17 personal computer · Data format The CI-V system can be operated using the following data formats. A data area or sub command is added for some commands. CONTROLLER TO IC-718 q w e r t y u mini-plug cable OK MESSAGE TO CONTROLLER Data area FD FE FE E0 5E FB FD FE FE 5E E0 Cn Sc Preamble code (fixed) Transceiver's default address Controller's default address Command number (see table at right) Sub command number (see table at right) Preamble code (fixed) Controller's default address BCD code data for frequency or memory number entry Transceiver's default address End of message code (fixed) OK code (fixed) NG code (fixed) IC-718 TO CONTROLLER q w e r t y u NG MESSAGE TO CONTROLLER Data area FD FE FE E0 5E FA FD FE FE E0 5E Cn Sc Preamble code (fixed) Controller's default address Transceiver's default address Transceiver's default address Preamble code (fixed) Controller's default address Command number (see table at right) Sub command number (see table at right) BCD code data for frequency or memory number entry End of message code (fixed) End of message code (fixed) End of message code (fixed) 57 13 CONTROL COMMAND · Command table Command Sub command 00 -- 01 -- 02 -- 03 -- 04 -- 05 -- 06 -- -- 00 01 07 A0 B0 -- 08 -- 09 -- 0A -- 0B -- 00 01 0E D0 D3 00 0F 01 10 -- 11 -- 01 02 03 14 06 09 0A 0B 0C 0F 01 15 02 02 22 40 41 44 46 47 00 Description Send frequency data Send mode data Read Upper/Lower frequencies Read frequencies Read operating mode Set operating frequency Set mode Set VFO Set VFO A Set VFO B VFO A=B VFO A B Set Memory Set Memory CH Memory write Memory VFO Memory clear Scan stop Prog/Memo Scan Start Resume OFF Resume ON SPLIT OFF SPLIT ON Set TS ATT AF Gain RF Gain SQL Level NR Level CW Pitch RF Power MIC Gain KEY Speed BK-IN Delay Read SQL Open/Close Read SIG (S-meter) level PRE-AMP NB NR Auto Notch COMP VOX BK-IN Read ID 16 19 58 INTERNAL VIEW I Top view Caution: 14 Drive ID adj. [. . . ]

DISCLAIMER TO DOWNLOAD THE USER GUIDE ICOM IC-718

Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets...
In any way can't Lastmanuals be held responsible if the document you are looking for is not available, incomplete, in a different language than yours, or if the model or language do not match the description. Lastmanuals, for instance, does not offer a translation service.

Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual ICOM IC-718 will begin.

Search for a user manual

 

Copyright © 2015 - LastManuals - All Rights Reserved.
Designated trademarks and brands are the property of their respective owners.

flag