User manual ICOM IC-91A

[. . . ] INSTRUCTION MANUAL VHF/UHF FM TRANSCEIVER i91A i91AD VHF/UHF DIGITAL TRANSCEIVER This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. WARNING: MODIFICATION OF THIS DEVICE TO RECEIVE CELLULAR RADIO TELEPHONE SERVICE SIGNALS IS PROHIBITED UNDER FCC RULES AND FEDERAL LAW. Y The above photo shows IC-91AD. FOREWORD Thank you for purchase of this fine Icom product. [. . . ] MENU screen MESSAGE/POSITION RX MESSAGE (Push [MENU/LOCK]) (Rotate [DIAL], then push [ï](5). ) · The received message is displayed in RX MESSAGE screen. RX MESSAGE r MESSAGE: The automatic reply function replies to calls by a station that specified your call sign. Two methods of replying are available-- one is making a reply call with your own call sign, and other one is making a reply call with reply voice audio that has been recorded in DV voice memory. D Automatic reply function setting q Enter "AUTO REPLY" in DV set mode. 92) MENU screen DV SET MODE AUTO REPLY (Push [MENU/LOCK]) (Rotate [DIAL], then push [ï](5). ) · AUTO REPLY screen is displayed. Hello! :BACK :CALLER wRotate [DIAL] or push [](8) to display the station call sign. RX MESSAGE r CALLER: w Rotate [DIAL] to select the desired reply condition. OFF : Deactivate the automatic reply function. (default) ON : Reply to the call with your own call sign. VOICE : Reply to the call with the recorded voice memory. AUTO REPLY r OFF BBBBBB / :BACK :MSG ePush [ï](5) or [](4) to return to MESSAGE/POSITION screen. r Push [MENU/LOCK] to return to frequency indication. ON VOICE e Push [ï](5). · Returns to DV SET MODE screen automatically. r Push [MENU/LOCK] to return to frequency indication. 54 DV MODE OPERATION (Optional UT-121 is required for IC-91A) 7 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 55 D Voice memory recording for automatic reply IMPORTANT!Deactivate the dualwatch function and set minimum [VOL] level when recording the DV voice memo. Otherwise received audio or unwanted noise from A band is also recorded into the voice memory. qSelect DV mode in B band, and deactivate the priority watch (p. w Enter "REPLY VOICE" in DV voice memo set mode. MENU screen DV VOICE MEMO REPLY VOICE (Push [MENU/LOCK]) (Rotate [DIAL], then push [ï](5). ) · REPLY VOICE screen is displayed. REPLY VOICE r REPLY D Play-back or erase the voice memory q Push [MENU/LOCK] to select menu mode indication. wRotate [DIAL] to select "DV VOICE MEMO, " then push [ï](5). eRotate [DIAL] to select "REPLY VOICE, " then push [ï](5). · REPLY VOICE screen is displayed. rTo play-back the recorded voice memory, push [ï](5). · Push [ï](5) again to pause, push [](6) to cancel the play-back. tTo erase the recorded voice memory, push and hold [CLR](1) for 1 sec. V : :BACK PTT:G PTT: CLR:CLR eWhile pushing and holding [PTT], speak into the microphone. · Up to 10 seconds of message is recordable. · The recording stops after 10 second or when [PTT] is released. r Push [](4) to return to DV VOICE MEMO screen. t Push [MENU/LOCK] to return to frequency indication. [DIAL] [](2)/[](8) [ï](5) [](6) 7 DV MODE OPERATION (Optional UT-121 is required for IC-91A) I EMR communication The EMR communication mode is available for digital mode operation. In the EMR communication mode, no call sign setting is necessary. When an EMR communication mode signal is received, the audio (voice) will be heard at the specified level even the volume setting level is set to minimum level, or digital call sign/digital code squelch is in use. qSet the desired frequency in 144 or 440 MHz band then push and hold [EMR](. ) until 3 short and 1 long beeps sound to turn the EMR setting ON. · "EMR" appears DV EMR I Low-speed data communication In addition to the digital voice communication, low-speed data communication is available. The optional OPC-1529R DATA COMMUNICATION CABLE and serial data communication software (purchase locally) are required in addition. The optional RS-91 REMOTE CONTROL SOFTWARE (OPC-1529R supplied) also includes a low-speed data communication capability. [. . . ] Battery life: 5 hrs. (approx. ; VHF, FM, high power, Tx : Rx : Standby = 1:1:8) · HM-75A REMOTE CONTROL MICROPHONE Allows you to remotely select operating channels, etc. · HM-131 SPEAKER-MICROPHONE For operation while conveniently hanging the transceiver from your belt, etc. · HM-128/HM-153 EARPHONE-MICROPHONE Ideal for hands-free operation by clipping the microphone with the PTT switch to your lapel or breast pocket. · HS-85 HEADSET WITH VOX/PTT UNIT Hands-free headset with VOX control box. [. . . ]