User manual ICOM IC-AG-35

[. . . ] q Hand microphone (HM-151) . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 w DC power cable (OPC-1457) . . . . . . . . . . . . . . . . . . . . . . . . . . 1 e Spare fuse (ATC 5 A) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 r Spare fuse (ATC 30 A) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] w Push [F-3 ADJ] to select the threshold level setting condition. e Rotate [DIAL] to adjust the RTTY decoder threshold level. · Push and hold [F-4 DEF] for 1 sec. to select the default condition. Z r Push [Z(MENU/GRP)] to exit the RTTY decoder screen. [MENU/GRP] [F-3] [F-4] [DIAL] The UnShift On Space (USOS) function and new line code can be set in the RTTY decode set mode. 55) 54 4 RECEIVE AND TRANSMIT D RTTY decode set mode This set mode is used to set the decode USOS function, etc. q Push [MODE] momentarily to select RTTY mode. · After RTTY mode is selected, push [MODE] for 1 sec. to toggle between RTTY and RTTY-R modes. w Select S-1. · Push and hold [MENU/GRP] for 1 sec. once or twice to select the menu group S. · Push [MENU/GRP] momentarily one or more times to select the menu S-1. [MENU/GRP] [F-1] [F-2] [F-4] [DIAL] e Push [F-2 DEC] momentarily to turn the RTTY decoder ON. · RTTY decoder screen appears. r Push [F-4 SET ] to select the RTTY decode set mode. t Push [F-1 ] or [F-2 ] to select the desired set item. y Set the desired condition using [DIAL]. · Push [F-4 DEF] for 1 sec. to select a default condition or value. Z u Push [Z(MENU/GRP)] to exit from set mode. 1 RTTY Decode USOS This item selects the USOS (UnShift On Space) function of the internal RTTY decoder. 74) M While "M-3" is selected, push [F-3 AGC] momentarily one or more times to select AGC fast, AGC middle and AGC slow. · Push and hold [MENU/GRP] for 1 sec. once or twice to select the menu group M. · Push [MENU/GRP] momentarily one or more times to select the menu M-3. ·" , " " " and " " appears when the fast time constant, middle time constant and slow time constant is selected, respectively. · Twin PBT (passband tuning) (p. 77) Push [PBT/M-ch/RIT] (switch) momentarily once or twice to select the twin PBT ON or OFF (M-ch RIT). · PBT indicator lights green when the twin PBT is selected. M While "M-3" is selected, push and hold [F-3 AGC] for 1 sec. to enter the AGC set mode. · Push [F-2 FAST], [F-3 MID] or [F-4 SLOW] to select the time constant, then rotate [DIAL] to adjust the time constant. Rotate [PBT/M-ch/RIT] (controls­inner/outer). · Push [PBT/M-ch/RIT(CLR)] to clear the settings. · Noise blanker (p. 78) Push [NB/ADJ] to turn the noise blanker ON and OFF. ·" " appears when the noise blanker is set to ON. Push and hold [NB/ADJ] for 1 sec. to enter the noise blanker set mode, then rotate [DIAL] to adjust the threshold level, or noise pulse width. 57 RECEIVE AND TRANSMIT 4 Convenient functions for receive (continued) · DSP noise reduction (p. 79) Push [NR/LEV] to turn the DSP noise reduction ON and OFF. ·" " appears when the DSP noise reduction is set to ON. · Auto notch filter (p. 80) Push [ANF/· REC] to turn the auto notch filter ON and OFF. ·" " appears when the auto notch filter is set to ON. Push [NR/LEV] for 1 sec. to enter the noise reduction level set mode, then rotate [DIAL] to adjust the DSP noise reduction level. [. . . ] 2E / 2F Description Numerals Alphabetical characters Word space Symbol Symbol Symbol D Split/Duplex frequency setting The following data sequence is used when sending/reading the split or duplex frequency setting. q X 0 X w X 0 e X r* XX 10 MHz digit: 0 (fixed) 100 Hz digit: 0 (fixed) 100 kHz digit: 0--9 10 kHz digit: 0--9 1 MHz digit: 0--4 X 1 Hz digit: 0­9 e X 2nd digit: 0­7 1 kHz digit: 0--9 D Codes for memory name contents To send or read the desired memory name settings, the character codes, instruction codes for memory keyer contents as above, and the following are used. · Character codes-- Alphabetical characters Character ASCII code Character ASCII code a­z 61­7A -- -- · Character codes-- Symbols Character ASCII code Character !3F " ' 27 ` + 2B ­ : 3A ; = 3D < > 3E ( ) 29 [ ] 5D { } 7D | ­ _ 5F @ 40 *No need to enter for duplex frequency setting. ASCII code 23 25 5C 22 60 2D 3B 3C 28 5B 7B 7C 7E D Repeater tone/tone squelch frequency setting The following data sequence is used when sending/reading the DTCS code and polarity setting. [. . . ]