User manual ICOM IC-E7

[. . . ] INSTRUCTION MANUAL VHF/UHF DUAL BAND FM TRANSCEIVER iE7 This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. WARNING: MODIFICATION OF THIS DEVICE TO RECEIVE CELLULAR RADIO TELEPHONE SERVICE SIGNALS IS PROHIBITED UNDER FCC RULES AND FEDERAL LAW. FOREWORD Thank you for purchasing this Icom product. The IC-E7 VHF/UHF DUAL BAND FM TRANSCEIVER is designed and built with Icom's superior technology and craftsmanship. [. . . ] · The bank can also be selected by pushing [BAND] (TS·LOCK) several times. Bank is selected with WFMAM -DUP T SQL + w Rotate [DIAL] to select the desired memory channel. eWhile pushing and holding [CALL] (MODE·SCAN), rotate [DIAL] to select "BANK. " · After releasing [CALL] (MODE·SCAN), "-- -- -- --" is displayed instead of the frequency indication, and only " " indicator blinks. · Bank group and channel number is displayed if the selected memory channel has already been assigned to a bank. · "BANK" can also be selected by pushing [CALL] (MODE·SCAN) several times. [DIAL] WFMAM -DUP T SQL DTCS ATT VOL PRIO P SKIP MR 9 5 LOW 1 t Rotate [DIAL] to select the desired bank channel number. · Vacant bank channel numbers are only be displayed. Bank channel is selected with WFMAM -DUP T SQL DTCS ATT DTCS ATT VOL PRIO P SKIP MR 9 5 LOW 1 VOL PRIO P SKIP MR 9 5 LOW 1 SCAN SCAN After [CALL] released WFMAM -DUP T SQL S. MW yPush and hold [V/M] (SKIP·S. MW) for 1 sec. to set the channel into the bank. · Return to the previous indication. DTCS ATT S. MW SET VOL PRIO P SKIP MR 9 5 LOW 1 25 MEMORY/CALL CHANNELS 6 Memory bank selection qPush [V/M] (SKIP·S. MW) to select memory mode, if desired. wWhile pushing and holding [BAND] (TS·LOCK), rotate [DIAL] to select the desired bank (A to H, J, L, N, O to R, T, U and Y). · The bank can also be selected by pushing [BAND] (TS·LOCK) several times. · The only programmed banks are displayed. [DIAL] VOL PRIO P SKIP MR 9 5 LOW 1 VOL PRIO P SKIP MR 9 5 LOW 1 WFMAM -DUP T SQL DTCS ATT WFMAM -DUP T SQL DTCS ATT VOL PRIO P SKIP MR 9 5 LOW 1 VOL PRIO P SKIP MR 9 5 LOW 1 Rotate [DIAL] while pushing [BAND] WFMAM -DUP T SQL Only programmed banks appear WFMAM -DUP T SQL DTCS ATT DTCS ATT 6 Auto write channels eRotate [DIAL] to select the bank channel. · Only programmed channels are displayed. SCAN WFMAM -DUP T SQL DTCS ATT S. MW SET VOL PRIO P SKIP MR 9 5 LOW 1 Bank initial Bank channel number rTo return to regular memory operation, rotate [DIAL] while pushing and holding [BAND] (TS·LOCK), or push [BAND] (TS·LOCK) several times. Push Push and hold Dual operation 26 6 MEMORY/CALL CHANNELS Programming memory/bank name Each memory channel can be programmed with an alphanumeric channel name for easy recognition and that can be indicated independently by channel. q Push [V/M] (SKIP·S. MW) to select memory mode. w Rotate [DIAL] to select the desired memory channel. ePush and hold [V/M] (SKIP·S. MW) for 1 sec. to enter select memory write mode. · 1 short and 1 long beep sound. ·" " indicator and memory channel number blink. WFMAM -DUP T SQL tWhile pushing and holding [FUNC], rotate [DIAL] to select the desired character. · The selected character blinks. y Rotate [DIAL] to move the cursor to left or right. Memory name WFMAM -DUP T SQL Bank name WFMAM -DUP T SQL DTCS ATT DTCS ATT VOL PRIO P SKIP MR 9 5 LOW 1 VOL PRIO P SKIP MR 9 5 LOW 1 DTCS ATT VOL PRIO P SKIP MR 9 5 LOW 1 uRepeat steps t and y until the desired 6-character channel names are displayed. iPush [CALL] (MODE·SCAN) several times, or rotate [DIAL] while pushing and holding [CALL] (MODE·SCAN) to select "S. MW. " WFMAM -DUP T SQL DTCS ATT rWhile pushing and holding [CALL] (MODE·SCAN), rotate [DIAL] to select "M NAME" or "B NAME" when programming the memory name or the bank name, respectively. · Name type can also be selected by pushing [CALL] (MODE·SCAN) several times. · After releasing [CALL] (MODE·SCAN), an under bar blinks for the first digit instead of the frequency indication, and only " " indicator blinks. Memory name selection WFMAM -DUP T SQL VOL PRIO P SKIP MR 9 5 LOW 1 oPush and hold [V/M] (SKIP·S. MW) for 1 sec. to program the name and exit the channel name programming. · 3 beeps sound. Bank name selection WFMAM -DUP T SQL · Available characters A to Z, 0 to 9, (, ), , +, ­, . , /, :, = and space. DTCS ATT DTCS ATT VOL PRIO P SKIP MR 9 5 LOW 1 VOL PRIO P SKIP MR 9 5 LOW 1 27 MEMORY/CALL CHANNELS 6 Selecting display type During memory mode operation, the programmed memory name, bank name or the channel number can be displayed instead of the frequency at your preference. WFMAM -DUP T SQL D Selecting bank channel indication During bank channel operation, the bank channel number can also be displayed instead of the memory channel number indication. Memory channel No. indication WFMAM -DUP T SQL DTCS ATT VOL PRIO P SKIP MR 9 5 LOW 1 WFMAM -DUP T SQL DTCS ATT DTCS ATT 6 Push [BAND] momentarily while pushing [FUNC] WFMAM -DUP T SQL VOL PRIO P SKIP MR 9 5 LOW 1 VOL PRIO P SKIP MR 9 5 LOW 1 DTCS ATT Push [BAND] SCAN VOL PRIO P SKIP MR 9 5 LOW 1 S. MW WFMAM -DUP T SQL DTCS ATT WFMAM -DUP T SQL DTCS ATT SET WFMAM -DUP T SQL DTCS ATT VOL PRIO P SKIP MR 9 5 LOW 1 VOL PRIO P SKIP MR 9 5 LOW 1 Auto write channel No. VOL PRIO P SKIP MR 9 5 LOW 1 Bank channel No. [. . . ] Memory channel selection q Push [V/M] to select memory mode. w Rotate [DIAL] to set the desired memory channel. · While pushing [FUNC], dial rotation changes memory channel in 10 channels steps. Key lock function While pushing and holding [FUNC], push [BAND] for 1 sec. to toggle the key lock function ON and OFF. · " L " appears when the lock function is in use. Attenuator function While pushing and holding [FUNC], push [SQL] to toggle the attenuator function ON and OFF. · "ATT" appears when the attenuator function is in use. Monitor function Push and hold [SQL]. · The 1st segment of S/RF meter blinks. Transmit power setting While pushing and holding [FUNC], push [PTT] to toggle the transmit output power High and Low. · "LOW" appears when the low output power is selected. 16 POCKET GUIDE 81 Memory bank channel selection q Push [V/M] to select memory mode. w Push [BAND] several times, or while pushing and holding [BAND], rotate [DIAL] to select the desired bank group. [. . . ]