User manual ICOM IC-E90

[. . . ] INSTRUCTION MANUAL iE90 MULTIBAND FM TRANSCEIVER This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. WARNING: MODIFICATION OF THIS DEVICE TO RECEIVE CELLULAR RADIO TELEPHONE SERVICE SIGNALS IS PROHIBITED UNDER FCC RULES AND FEDERAL LAW. FOREWORD Thank you for purchasing this Icom product. The IC-E90 MULTIBAND TRANSCEIVER is designed and built with Icom's superior technology and craftsmanship. [. . . ] 29, 71) · Subaudible tone and tone squelch frequencies (p. 72) · DTCS code with code phase mode (pgs. 47) t MEMORY/CALL CHANNELS 34 5 MEMORY/CALL CHANNELS D Default memory contents example CHANNEL DESCRIPTION · Regular memory channel · Default memory channel example 000­499 (Memory channel; Mch) Mch 000 Mch 001 Mch 002 151. 000 MHz 145. 000 MHz 430. 000 MHz CHANNEL C0­C4 (Call channel) DESCRIPTION · Calling channel for amateur bands · Can be used as regular memory channel · Default call channel example C0 151. 000 MHz C1 145. 000 MHz C2 430. 000 MHz *C3 and 4 are blank channels. *Mch 003­499 are blank channels. · Program scan edge channel 25 pairs (50 channels) · Default scan edge example 0A/0B­ 24A/24B (Scan edge channel) 0A: 1110. 495 MHz 1A: 1150. 000 MHz 2A: 1144. 000 MHz 3A: 1430. 000 MHz 1 0B: 440. 000 MHz 1B: 1152. 000 MHz 2B: 1146. 000 MHz 3B: 1440. 000 MHz 1 *4A/4B­24A/24B are blank channels. 1 35 MEMORY/CALL CHANNELS 5 I Calling up memory channels Memory channels can be selected with the [DIAL] and keypad. · Blank channels cannot be selected via [DIAL]. · Blank channels can be selected via keypad. · Previously selected channels appear when the wrong memory channel number is entered. [DIAL] D Selecting with tuning dial q Push [MR] to select memory mode. w Rotate [DIAL] to select the desired memory channel. Memory mode indication FM CONVENIENT The memory channels (000­099) can be selected with 1 or 2 digits plus [MR]. · Selecting memory channel 005. Push [2], [4] and [MR]. t MEMORY/CALL CHANNELS 36 Appears Memory channel number D Check contents of all memory channels q Push [MR S. MW] for 1 sec. to enter memory write condition. · Memory channel readout blinks. FM D Selecting with keypad q Push [MR] to select memory mode. w Push the desired numeral keys to select the desired memory channel. [MR S. MW] · Selecting memory channel 001. Push [4], [9] and [9]. V 1 4 7 D TONE 2 5 8 H/L 3 6 9 TS keypad 0 w Rotate [DIAL] to check the desired memory channel. Rotating [DIAL] while pushing [BAND] also selects all memory channels. DUP SKIP M. N RIT T. SCAN SET 5 MEMORY/CALL CHANNELS I Programming memory channels Program the desired frequency into a memory channel, call channel or scan edge channel as follows. The memory channels are shared with all bands. Memory channels 003­499 are blank (non-programmed) channels as a factory setting. [DIAL] D Programming a memory channel [EXAMPLE]: 433. 520 MHz into Mch 11 q Select VFO mode with [VFO]. w Set the desired frequency: Select the desired band with [BAND]. offset frequency, duplex direction, subaudible tone frequency, etc. ), if required. to indicate memory channels. · Memory channel indicator " " and channel readout blinks. · Do not hold [MR S. MW] for more than 2 sec. , otherwise the previously selected memory channel contents will be overwritten. [BAND] [VFO] [MR S. MW] r Rotate [DIAL] to select the desired channel. · Call channels (C0­C4), VFO (VF) and scan edge channels (0A/0B­24A/24B), as well as regular memory channels, can be programmed in this way. t Push [MR S. MW] for 1 sec. to program. q, w Set the frequency. FM P SKIP e Push [MR S. MW] for 1 sec. FM r Select the desired channel. t Push [MR S. MW] for 1 sec. FM P SKIP " " and memory channel readout blinks. VFO mode is selected after writing. 37 MEMORY/CALL CHANNELS 5 D Auto memory channel increment While programming a memory channel, the next memory channel can be selected automatically. This is convenient when programming memory channels one after another. or more, at step t of the left section, to select the next memory channel automatically. Push [MR S. MW] for 1 sec. FM I Transferring memory contents to VFO This is convenient when operating around a memory or call channel. t MEMORY/CALL CHANNELS 38 q Push [VFO] several times to select VFO A or B to be transferred. e Set the desired memory channel with [DIAL]. · Call or scan edge channel contents can be transferred in the same manner. Select a call channel in this case. Keep pushing [MR S. MW]. FM P SKIP r Push [MR S. MW] for 2 sec. [. . . ] w While pushing and holding [BAND], [VFO] and [MR], turn power ON. D BAND iC- e90 A 1 V D 2 TONE 3 H/L VFO MHz I Exchange [DIAL] and []/[] assignment Push and hold [1 VD] for 1 sec. · Partial reset q Turn power OFF. w While pushing and holding [VFO], turn power ON. MODE SCAN B DUP 4 SKIP 5 7 M. N 6 8 T. SCAN 0 9 SET TS MR RIT S. MW C CALL/TV LOCK . DTMF. M I VFO/MEMORY MODE selection VFO mode : Push [VFO]. [. . . ]