User manual ICOM IC-F1710
Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets... DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!
If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Lastmanuals provides you a fast and easy access to the user manual ICOM IC-F1710. We hope that this ICOM IC-F1710 user guide will be useful to you.
Lastmanuals help download the user guide ICOM IC-F1710.
You may also download the following manuals related to this product:
ICOM IC-F1710 BROCHURE (1799 ko)
Manual abstract: user guide ICOM IC-F1710
Detailed instructions for use are in the User's Guide.
[. . . ] INSTRUCTION MANUAL
VHF MOBILE TRANSCEIVER
This device complies with Part 15 of the FCC Rules. Operation is subject to the condition that this device does not cause harmful interference.
UHF MOBILE TRANSCEIVER
This model is IC-F1821/D or IC-F2821/D
READ ALL INSTRUCTIONS carefully and completely before using the transceiver.
RWARNING!NEVER connect the transceiver to a power source of more than 16 V DC such as a 24 V battery. If an incorrect connection is made after cutting, the transceiver might be damaged. [. . . ] w If the transceiver is programmed for a start up password, input the digit codes as directed by your dealer.
· 10-keypad* can be used for password input. *IC-F1821/D or IC-F2821/D only: · The keys as below can be used for password input: The transceiver detects numbers in the same block as identical. Therefore "01234" and "56789" are the same.
*In this instruction manual, these keys are from the left, called [P0]/[P1]/[P2]/[P3]/[P4].
AUTOMATIC SCAN TYPE: Channel setting is not necessary for this type. Scanning stops when receiving a call.
e When the "PASSWORD" indication does not clear after inputting 6 digits, the input code number may be incorrect. Turn the power off and start over in this case.
I Call procedure
When your system employs tone signaling (excluding CTCSS and DTCS), the call procedure may be necessary prior to voice transmission. The tone signalling employed may be a selective calling system which allows you to call specific station(s) only and prevent unwanted stations from contacting you. q Select the desired TX code channel, 2/5-tone code, Individual ID code* or Talkgroup ID code* according to your System Operator's instructions.
· This may not be necessary depending on programming. *Digital mode operation only.
I Receiving and transmitting
Receiving: q Push [ ] to turn the power ON. w Push [CH Up] or [CH Down], or rotate [CH Up/Down] to select a channel, in sequence. e When receiving a call, adjust the audio output level to a comfortable listening level. Transmitting: Wait for the channel to become clear to avoid interference. q Take the microphone off hook.
· 2-tone, 5-tone mute may be released. (The `audible' condition is selected and BUSY indicator lights green. ) · A priority channel may be selected automatically.
w Push the call key (assigned to one of the dealer programmable keys; except for the Digital mode operation) or [PTT]. e After transmitting, the remainder of your communication can be carried out in the normal fashion.
Selective calling Non-selective calling
w Wait for the channel to become clear.
· The channel is busy when BUSY indicator lights green.
e Push [CALL] when initiating a call from your side.
· Coded audio may be heard from the transceiver, then " " appears. · This operation may not be necessary depending on your signaling system. Ask your dealer for details.
r While pushing and holding [PTT], speak into the microphone at your normal voice level. Hold the microphone 5 to 10 cm (2 to 4 inches) from your mouth, then speak into the microphone at a normal voice level.
BASIC OPERATION D TX code channel selection
If the transceiver has [TX Code CH Select] assigned to it, the indication can be toggled between the operating channel number (or name) and TX code channel number (or name). When the TX code channel number (or name) is displayed, [CH Up]/[CH Down] selects the TX code channel. USING [TX CODE CH SELECT] KEY: q Push [TX Code CH Select]-- a TX code channel number (or name) appears. w Push [CH Up] or [CH Down], or rotate [CH Up/Down] to select the desired TX code channel. e Push [Call] (or [PTT] during MSK operation) to transmit the selected TX code. USING [TX CODE CH UP]/[TX CODE CH DOWN] KEY: If the transceiver has a [TX Code CH Up], [TX Code CH Down] or [TX Code CH Up/Down] key assignment, the programmed TX code channel can be selected directly when pushed or rotated. [. . . ] Otherwise no TX modulation or AF output is available.
q Dimmer cont. GND
CONNECTION AND MAINTENANCE
A key element in the performance of any communication system is an antenna. Contact your dealer about antennas and the best places to mount them.
· RMK-2 SEPARATION KIT + OPC-607/OPC-608/OPC-609 SEPARATION CABLE Allows you to install the transceiver main unit separately from the front panel for operating convenience. The same as supplied with the transceiver (depending on version. ) · HM-100TN/HM-100N/HM-148 HAND MICROPHONE HM-100TN : Hand microphone with a DTMF keypad. [. . . ]
DISCLAIMER TO DOWNLOAD THE USER GUIDE ICOM IC-F1710
Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets...
In any way can't Lastmanuals be held responsible if the document you are looking for is not available, incomplete, in a different language than yours, or if the model or language do not match the description. Lastmanuals, for instance, does not offer a translation service.
Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual ICOM IC-F1710 will begin.