User manual ICOM IC-F210

[. . . ] INSTRUCTION MANUAL VHF TRANSCEIVER iF110 UHF TRANSCEIVER iF210 IMPORTANT READ ALL INSTRUCTIONS carefully and completely before using the transceiver. PRECAUTION RWARNING!NEVER connect the transceiver to an AC outlet. This may pose a fire hazard or result in an electric shock. NEVER connect the transceiver to a power source of more than 16 V DC such as a 24 V battery. [. . . ] to lock all programmable LOCK keys except the following: · [CALL] (incl. [CAL A] and [CAL B]), [MONI] and [EMER] keys. 4 1 PANEL DESCRIPTION ¡ CALL KEY Transmit a 2-tone, 5-tone code. CALL · Call transmission is necessary before you call another station depending on your signaling system. · The [CAL A] and/or [CAL B] keys may be available when your system employs selective `Individual/Group' calls. Contact your dealer about which call is assigned to each key. ¡ OUTPUT POWER SELECTION KEYS Select the transmit output power temporarily, or H/L permanently, depending on the pre-setting. · Contact your dealer for the output power level for each selection. CAL A CAL B ¡ TALK AROUND KEY Turns the talk around function ON and OFF. TA · The talk around function equalizes the transmit frequency to the receive frequency for mobile-to-mobile communication. ¡ EMERGENCY KEY Push and hold the key to transmit an emergency call. EMER · If you want to cancel the emergency call, push and hold (or push) the key again before transmitting the call. · Depending on the pre-setting, the emergency call is transmitted one time only, or repeatedly, until receiving a control code. ¡ WIDE/NARROW KEY Push this key to toggle the bandwidth between W/N wide or narrow. ¡ DTMF AUTODIAL KEY Push this key to display the text of the DTMF DTMF channel number and set the desired channel number via the [ ]/[ ] key. Then, push this key again to transmit a specified DTMF code. ¡ HOOK SCAN When the Hook Scan function is turned ON, push HOOK this key to stop scanning temporarily. Push this key again to re-start scanning. ¡ TX CODE KEY Select a transmit 5-tone code (station code) chanTX CH nel. 5 PANEL DESCRIPTION ¡ SCRAMBLER KEY Push and hold to turn the voice scrambler funcSCRM tion ON. Push this key to turn the voice scrambler function OFF. NOTE: · The optional UT-109 (#02) or UT-110 (#02) VOICE SCRAMBLER UNIT is required. ­ UT-109: Non-rolling type. 1020 (4 groups × 255) codes are available. 1 ¡ USER SET MODE KEY Changes the contents of the items in the User Set SET mode. 10. · Push and hold this key for 1 sec. Push this key again momentarily to select the desired item. Push [ ]/[ ] to set the desired level/condition. Push and hold this key again to exit set mode. · User set mode also available via the `Power ON function'. · This transceiver requires version #02 of these units. Do not install version #01, as they are not compatible. · Some PC board modifications are required when installing UT-109 or UT-110. [. . . ] 4 *Function name stickers There are no names on the programmable function keys since the functions can be freely assigned to these keys. Attach the supplied function name stickers above the appropriate keys for easy recognition of that key's assigned function. 14 4 CONNECTION AND MAINTENANCE I Mounting the transceiver The universal mounting bracket supplied with your transceiver allows overhead mounting. · Mount the transceiver securely with the 4 supplied screws to a thick surface which can support more than 1. 5 kg. I Optional UT-105, UT-108 or UT-111 installation Install the optional UT-105, UT-108 or UT-111 unit as follows: q Turn the power OFF, then disconnect the DC power cable. w Unscrew the 4 cover screws, then remove the bottom cover. [. . . ]