User manual ICOM IC-F21BR
Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets... DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!
If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Lastmanuals provides you a fast and easy access to the user manual ICOM IC-F21BR. We hope that this ICOM IC-F21BR user guide will be useful to you.
Lastmanuals help download the user guide ICOM IC-F21BR.
Manual abstract: user guide ICOM IC-F21BR
Detailed instructions for use are in the User's Guide.
[. . . ] INSTRUCTION MANUAL
VHF BRS TRANSCEIVER
UHF BRS TRANSCEIVER
This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
SAFETY TRAINING INFORMATION
Your Icom radio generates RF electromagnetic energy during transmit mode. This radio is designed for and classified as "Occupational Use Only", meaning it must be used only during the W ARN ING course of employment by individuals aware of the hazards, and the ways to minimize such hazards. This radio is NOT intended for use by the "General Population" in an uncontrolled environment. [. . . ] · Use the battery until it becomes almost completely exhausted under normal conditions. D Battery pack life When the operating period becomes extremely short even after charging the battery pack fully, a new battery pack is needed.
NOTE: The charger rapidly charges a battery pack to a specified level, not a completed level, to prevent overcharging. Leave the battery pack in the charger for a few more hours (up to 15 hours; depending on battery condition) after the LED indicator turns green, to charge the battery completely. 10
` Battery case (Option)
When using a BP-208 OPTIONAL BATTERY CASE attached to the transceiver, install 6 AA (R6) size alkaline batteries as illustrated below. NOTE: Output power is automatically reduced to 1 W to retain sufficient power in case of an emergency, etc.
D CAUTIONS · Use ALKALINE batteries only. · Make sure all battery cells are the same brand, type and capacity. Either of the above may cause a fire hazard or damage the transceiver, if ignored. · Never incinerate used battery cells since internal battery gas may cause them to rupture. If the battery case gets wet, be sure to wipe it dry before using it.
` Set mode
Set mode is used for programming infrequently changed values or conditions of functions. · All settings performed with [CH 1/CH 2], [OFF/VOL], [MONI], [PTT] and [W/N] keys. D SETTING THE OPERATION FREQUENCY The operating frequency can be selected from GMRS* ( Plus 7 frequencies shared with FRS*) and BRS frequencies. 1516 for IC-F21BR)
* IC-F21BR (UHF model) only.
[CH 1/CH 2] [OFF/VOL]
[MONI] [PTT] [W/N]
D SETTING THE CTCSS TONE FREQUENCY
CTCSS (Continuous Tone Coded Squelch System) encoder/decoder are standard, providing quiet stand-by. 1718) D FREQUENCY FIND This transceiver can detect the operating frequency by scanning the all pre-programmed channels. 19) D CTCSS FIND This transceiver can detect the CTCSS tone frequency in the received signal. 20)
D IC-F11BR (VHF) SETTING THE OPERATION FREQUENCY The operating frequency can be selected from 36 frequencies. (See right. ) Select the frequencies you desire from the frequency table and assign them to CH 1 and CH 2. 0 (OFF) q While pushing and holding [PTT], [MONI] and [W/N], turn [OFF/VOL] to power ON. w Select the desired CH 1 or CH 2 that you want to assign the frequency to. r Push [PTT] the necessary number of times to choose the 10 digit of the desired channel from the channel list. y Push [PTT] the necessary number of times to choose the 1 digit of the desired channel from the frequency list. 28 as CH1; q While pushing and holding [PTT], [MONI] and [W/N], turn [OFF/VOL] to power ON. y Push [PTT] eight times to choose the 1 digit of the desired channel. [. . . ] · Push and hold the [MONI], switch to select the audible condition. Any audio mute functions are cancelled All signals are received while pushing the [MONI] switch. Inaudible condition: This condition mutes ALL signals except those directed to you. Therefore you should check a channel's condition (busy or not) with the monitor function before transmitting. [. . . ]
DISCLAIMER TO DOWNLOAD THE USER GUIDE ICOM IC-F21BR
Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets...
In any way can't Lastmanuals be held responsible if the document you are looking for is not available, incomplete, in a different language than yours, or if the model or language do not match the description. Lastmanuals, for instance, does not offer a translation service.
Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual ICOM IC-F21BR will begin.