User manual ICOM IC-F2500
Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets... DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!
If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Lastmanuals provides you a fast and easy access to the user manual ICOM IC-F2500. We hope that this ICOM IC-F2500 user guide will be useful to you.
Lastmanuals help download the user guide ICOM IC-F2500.
You may also download the following manuals related to this product:
ICOM IC-F2500 BROCHURE (204 ko)
Manual abstract: user guide ICOM IC-F2500
Detailed instructions for use are in the User's Guide.
[. . . ] NEVER place the transceiver where normal operation of
the vehicle may be hindered or where it could cause bodily injury.
SAVE THIS INSTRUCTION MANUAL -- This instruction manual contains important operating instructions for the IC-F111S/F121S VHF TRANSCEIVER and ICF211S/F221S UHF TRANSCEIVER.
DEFINITION Personal injury, fire hazard or electric shock RWARNING may occur. and the logo are registered trademarks of Icom Incorporated (Japan) in the United states, the United Kingdom, Germany, France, Spain, Russia and/or other countries. SmarTrunk IITM is a Trademark of SmarTrunk Systems, Inc.
NEVER allow children to touch the transceiver. NEVER expose the transceiver to rain, snow or any liquids.
TABLE OF CONTENTS
the supplied microphone only. [. . . ] r POWER SWITCH [POWER] Push to turn the power ON and OFF.
· The following functions are available at power ON as options: - Automatic scan start - Password prompt - Set mode
w MICROPHONE CONNECTOR Connect the supplied microphone or optional DTMF microphone. The pin assignments may be different and the transceiver may be damaged. 1
I Function LED
D MICROPHONE The supplied microphone has a PTT switch and a hanger hook.
q CHANNEL INDICATORS Indicates the operating channel. w TX/RX INDICATOR Lights red: while transmitting Lights green: while the channel is busy Blinks orange (green and red blink simultaneously): when the specified 2-tone, 5-tone call is received. Green and red blink alternately: cloning error e ACTIVATED KEY INDICATOR (LP 0/1/2) Appears when a pre-programmed key function is activated. NOTE: When all function LEDs blink, check the DC battery voltage is not too high.
· The following functions are available when the microphone is on or off hook: - Automatic scan start when hook on. - Sets to `Audible' condition (unmute condition) when hook off.
¡ SCAN TAG KEY Adds or deletes the selected channel to the scan TAG group.
I Programmable function keys
The following functions can be assigned to [P0], [P1], [P2] and [P3] programmable function keys. Consult your Icom Dealer or System operator for details concerning your transceiver's programming. In the following explanations, programmable function names are bracketed. The specific switch used to activate the function depends on programming. CH UP
¡ PRIORITY CHANNEL KEYS Push these keys to select priority A or priority B PRI A channel, respectively.
¡ OPERATING CHANNEL KEYS Select an operating channel directly. ¡ USER SET MODE KEY Changes the contents of the items in the User Set SET mode. · User set mode also available via the `Power ON function'. · Some PC board modifications are required when installing UT-109 and UT-110. (p. 12) · Please contact your Dealer for details.
I Turning power ON
q Push [ ] to turn the power ON. w If the transceiver is programmed for a start up passcode, input the digit codes as directed by your Dealer.
· The keys in the table below can be used for password input: · The transceiver detects numbers in the same block as identical. Therefore "01234" and "56789" are same.
I Channel selection
Several types of channel selection are available. The methods may differ according to your system setup.
e When all channel indicator LEDs still blink after inputting 4 digits, the input code number is incorrect. KEY 0 5 1 6 2 7 3 8 4 9
NON-BANK TYPE: Push [CH UP]/[CH DN] to select the desired operating channel, in sequence; or, push one of the [CH 1] to [CH 4] keys to select a channel directly. When turning the power ON, the transceiver automatically starts scanning. Scanning stops when receiving a call or when taking the microphone off hook.
IMPORTANT: To maximize the readability of your signal: (1) Pause briefly after pushing [PTT] (2) Hold the microphone 2 to 5 cm from your mouth, then speak into the microphone at a normal voice level.
I Receiving and transmitting
RECEIVING: q Push [POWER] to turn the power ON. e When receiving a call, adjust the audio output level to a comfortable listening level. [. . . ] In this case you can "customize" transceiver operation to suit your preferences and operating style. Entering the user set mode: qWhile pushing and holding [P1] and [P2], push [POWER] to enter user set mode at power ON. The channel indicator lights respectively to indicate the function is selected. · Mount the transceiver securely with the 4 supplied screws to a thick surface which can support more than 1. 5 kg.
I Optional UT-108 installation
Install the optional UT-108 DTMF decoder unit as follows: q w e r Turn the power OFF, then disconnect the DC power cable. [. . . ]
DISCLAIMER TO DOWNLOAD THE USER GUIDE ICOM IC-F2500
Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets...
In any way can't Lastmanuals be held responsible if the document you are looking for is not available, incomplete, in a different language than yours, or if the model or language do not match the description. Lastmanuals, for instance, does not offer a translation service.
Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual ICOM IC-F2500 will begin.