User manual ICOM IC-F25SR

[. . . ] INSTRUCTION MANUAL PMR446 FM TRANSCEIVER iF25SR IMPORTANT READ ALL INSTRUCTIONS carefully and completely before using the transceiver. SAVE THIS INSTRUCTION MANUAL-- This instruction manual contains important operating instructions for the ICF25SR PMR446 FM TRANSCEIVER. EXPLICIT DEFINITIONS WORD RWARNING CAUTION NOTE DEFINITION Personal injury, fire hazard or electric shock may occur. No risk of personal injury, fire or electric shock. Icom, Icom Inc. and the logo are registered trademarks of Icom Incorporated (Japan) in the United States, the United Kingdom, Germany, France, Spain, Russia and/or other countries. All other products or brands are registered trademarks or trademarks of their respective holders. i PRECAUTIONS R CAUTION! [. . . ] 14. ) u Push [PTT] the necessary number of times to choose the 1 digit of the desired DTCS code number (grey column) from the list at right. i Push [Upper]. · Confirmation beep(s) is (are) emitted. 14. ) o If you want to use Inverse mode, push [PTT] once more. *You can skip this step, if you want to use Normal mode. !0 Push [Upper] to complete the setting. · A short beep is emitted. !1 Turn power OFF, then ON again. 16 (114) with Inverse mode assignment to channel 5 q Turn power OFF in advance. w While pushing and holding [PTT], [Upper] and [Lower], rotate [VOL] to turn the power ON. 15 BASIC OPERATION 3 e Rotate [CH selector] to select channel 5, then push and hold [Lower] until a long beep is emitted. r Push [PTT] once to choose the 1 (10 digit) of the code number 16. t Push [Upper] (a short beep is emitted, ) then push [PTT] six times to choose the 6 (1 digit) of the code number 16. y Push [Upper]. · A long beep and a short beep are emitted. 3 u Push [PTT] once more, to use Inverse mode. i Push [Upper] to complete the setting. · A short beep is emitted. o Turn the power OFF, and then ON again. · Available DTCS code list No. 01 02 03 04 05 06 07 08 09 10 51 52 53 54 55 56 57 58 59 60 Code 023 025 026 031 032 036 043 047 051 054 371 411 412 413 423 431 432 445 464 465 No. 11 12 13 14 15 16 17 18 19 20 61 62 63 64 65 66 67 68 69 70 Code 065 071 072 073 074 114 115 116 125 131 466 503 506 516 532 546 565 606 612 624 No. 21 22 23 24 25 26 27 28 29 30 71 72 73 74 75 76 77 78 79 80 Code 132 134 143 152 155 156 162 165 172 174 627 631 632 654 662 664 703 712 723 731 No. 31 32 33 34 35 36 37 38 39 40 81 82 83 84 00 Code 205 223 226 243 244 245 251 261 263 265 732 734 743 754 OFF No. 41 42 43 44 45 46 47 48 49 50 Code 271 306 311 315 331 343 346 351 364 365 16 3 BASIC OPERATION ` Find scan operation This transceiver can detect the CTCSS tone and DTCS code* in the received signal. By monitoring a signal that is being transmitted from the other station, you can determine the tone frequency or DTCS code* required to communicate with them. This function is very useful when you are going to communicate with unknown CTCSS tone or DTCS code* stations. Scans all of the CTCSS tone and DTCS code*, then stops when a matched tone or code* is detected. w While pushing and holding [Upper] and [Lower], rotate [VOL] to turn power ON. Do not select channel 16 before turning power ON. e Rotate [CH selector] to select the desired channel (1 to 15) that you want to assign the CTCSS tone or DTCS code* to. to start scan. · The LED indicator blinks green slowly. · Push [Upper] to stop the scan. t The scan pauses when the matched tone or code* is detected. · Push [Upper] to determine the detected tone or code* number, and stop the scan. [. . . ] 2) w Slide the base clip in the direction of the arrow until the base clip is locked and makes a `click' sound. 35 SWIVEL BELT CLIP 8 e Clip the belt clip to a part of your belt. And insert the transceiver into the belt clip until the base clip is inserted fully into the groove. 8 r Once the transceiver is locked in place, it swivels as illustrated below. Once the transceiver is locked in place, it will swivel 360 degrees. 36 8 SWIVEL BELT CLIP I Detaching q Turn the transceiver upside down in the direction of the arrow and pull out from the belt clip. 37 SWIVEL BELT CLIP 8 w Release the battery pack if it is attached. 2) e Pinch to lift the clip (q), and slide the base clip in the direction of the arrow (w). q w 8 CAUTION: HOLD THE TRANSCEIVER TIGHTLY, WHEN HANGING OR DETACHING THE TRANSCEIVER FROM THE BELT CLIP. [. . . ]