User manual ICOM IC-F2610

[. . . ] NEVER place the transceiver where normal operation of the vehicle may be hindered or where it could cause bodily injury. Place unit in a secure place to avoid inadvertent use by children. NEVER expose the transceiver to rain, snow or any liquids. Other microphones have different pin assignments and may damage the transceiver. Versions of the transceiver which display the "CE" on the serial number seal, comply with the essential requirements of the 89/336/EEC directive for Electromagnetic Compatibility. SmarTrunk IITM is a trademark of SmarTrunk Systems, Inc. ii DO NOT connect the transceiver to a power source using reverse polarity. This connection will not only blow fuses but also may damage the transceiver. DO NOT use or place the transceiver in areas with temperatures below ­20°C or above +55°C or, in areas subject to direct sunlight, such as the dashboard. AVOID operating the transceiver without running the vehicle's engine. [. . . ] CHANNEL SELECT FUNCTION When a key is assigned this function, push it to increment or decrement the operating channel. BANK UP/DOWN FUNCTION When a key is assigned this function, push it to increment or decrement the selected channel bank. PRIORITY CHANNEL A REWRITE FUNCTION When a key is assigned this function: Push momentarily to select PRIO A channel. Push and hold to set the current channel to PRIO A. DTMF RE-DIAL FUNCTION When a key is assigned this function, push it to automatically re-dial the most recent (manually transmitted) DTMF code. TX CODE KEY Selects a transmit 5-tone code (station code) chanCODE nel. · Push and hold to change the contents of the station code using the [CH UP]/[CH DN] keys. · Push to select a TX 5-tone code channel using the [CH UP]/[CH DN] keys after pushing this key. ID MEMORY READ KEY ID MR Recalls detected ID codes. · Push this key, then push [CH UP]/[CH DN] for selection. · Up to 5 ID's are remembered. Push and hold this key to erase all memorized ID's. OPT OPTION KEY TRUNKING GROUP KEY Push to select a trunking group (when operating in GRP SmarTrunk IITM mode). 5 1 PANEL DESCRIPTION TX CODE CHANNEL UP/DOWN FUNCTION When a key is assigned this function, push it to increment or decrement the TX code channel. TURBO SpeeDial A/B/C/D FUNCTIONS During SmarTrunk IITM operation, when a key is assigned this function, push it to automatically dial a commonly used number with one push. q w e r t y LOW CH09 173. 9 W LOW i output. u ACTIVATED KEY INDICATOR Appears or flashes to indicate the key directly below it has been activated. · Penalty timer Once the time-out timer is activated, transmission is further inhibited for a period determined by the penalty timer. I Receiving and transmitting RECEIVING: Push [ ] to turn power ON. Push [CH UP]/[CH DN] to select a channel. When receiving a call, adjust the volume to comfortable listening level. TRANSMITTING: Lift the microphone off the microphone hanger. · 5-tone mute may be released (the `audible' condition is selected and "[ ]" appears. · A priority channel may be selected automatically. Wait for the channel to become clear. · The channel is busy when "[ ]" appears. Push the [CALL] key when initiating a call from your side. · Coded audio may be heard from the transceiver, then "[ ]" appears. · This step may not be necessary depending on your signalling system. Ask your system operator or dealer. While pushing and holding [PTT], speak into the microphone at your normal voice level. Release [PTT] to receive. IMPORTANT: To maximize the readability of your signal: · Pause briefly after pushing [PTT]. · Hold the microphone 15 to 20 cm from your mouth, then speak into the microphone at a normal voice level. 8 OPERATION D Tx code channel selection If the transceiver has the [TX CH] key, display can be toggled with the operating channel number (or name) and Tx code channel number (or name). When the Tx code channel number (or name) is displayed, the [ ]/[ ] key selects the Tx code channel. TO SELECT A TX CHANNEL: Push [TX CH]--a Tx code channel appears. [. . . ] Enter the memory location (0­9, A, B, C, D), the telephone or subscriber number, then [1], [M] (or [3], [M] if for another system subscriber). · A high-pitched beep indicates successful programming. · Memories [A]­[D] are used for Turbo SpeeDial. D Last number redial Push [M], [M] to automatically redial the last number called. · A high-pitched beep indicates that the number is accepted. D System busy indication If all calls are busy, three low beeps sound after you initiate a call. Try the call again later. D Memory speed-dialing To automatically dial a commonly used number from memory: Push [M] followed by the memory location (0­9). D PTT dispatch operation Push [PTT] once (without dialing) to initiate a dispatch call. Begin talking after you hear three beeps (one short, highpitched, two very short, low-pitched). D Turbo SpeeDial To automatically dial a commonly used number with one push: Push one of the turbo SpeeDials ([A], [B], [C] or [D]). Receiving a dispatch call is indicated by the same three beep sequence. · It is not necessary to push [M] to answer a dispatch call. D Emergency call Push [0], [M] to initiate an emergency call. · Contact your dealer for details. 15 4 OPTIONAL SmarTrunk IITM OPERATION D Clear channel alerting If all channels are busy the transceiver automatically begins searching for an open channel and beeps every ten seconds. [. . . ]