User manual ICOM IC-F30GT-GS

Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets... DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!

Sponsored Links

If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Lastmanuals provides you a fast and easy access to the user manual ICOM IC-F30GT-GS. We hope that this ICOM IC-F30GT-GS user guide will be useful to you.

Lastmanuals help download the user guide ICOM IC-F30GT-GS.

ICOM IC-F30GT-GS : Download the complete user guide (598 Ko)

Manual abstract: user guide ICOM IC-F30GT-GS

Detailed instructions for use are in the User's Guide.

[. . . ] INSTRUCTION MANUAL VHF TRANSCEIVER UHF TRANSCEIVER iF30GT/GS iF40GT/GS This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must except any interference received, including interference that may cause undesired operation. FOREWORD Thank you for purchasing the IC-F30GT/GS, IC-F40GT/GS FM transceiver. READ ALL INSTRUCTIONS carefully and completely before using the transceiver. SAVE THIS INSTRUCTION MANUAL­This instruction manual contains important operating instructions for the transceiver. INSTALLATION NOTES · When transmitting with a portable radio, hold the radio in a vertical position with its microphone 2. 5 to 5 centimeters (1 to 2 in. ) away from your mouth. [. . . ] while pushing the [Moni] (LMR) or Any audio mute functions are cancelled [Moni (Audi)] (PMR) switch. Inaudible condition: This condition mutes ALL signals except those directed to you. Therefore you should check a channel's condition (busy or not) with the monitor function before transmitting. Only signals containing the · Push the [Moni] (LMR) or [Moni (Audi)] proper tone are received. (PMR) switch momentarily to select the inaudible condition. D TALK AROUND The talk around function changes duplex channels to simplex channels. · Duplex allows you to contact your base station, repeaters, etc. · Simplex allows you to contact other portable transceivers directly (portable-to-portable contact). Push the [Talk Around] switch to toggle the function ON and OFF. 13 4 PROGRAMMABLE FUNCTIONS D DTMF TRANSMISSION This function allows you to send a pre-programmed DTMF code to control a repeater, open another transceiver's squelch, etc. Manual transmission: Push the desired digit keys in sequence while pushing [PTT]. · Pushing [PTT] may not be necessary depending on programming. Automatic pre-programmed transmission: q Push the [DTMF Autodial] switch to select DTMF autodial mode, then push [CH Up] or [CH Down] to select the desired channel. D DTMF RE-DIAL FUNCTION This function allows you to transmit the last-used DTMF code at the push of a key. Push the [Re-dial] switch momentarily to activate the function. · The previously transmitted DTMF code is automatically transmitted. · If no code has been transmitted since turning the power ON, this function does not activate. D EMERGENCY FUNCTION The emergency function allows you to send an emergency signal quickly and easily to your Base Station, etc. to activate the emergency function. · The transceiver selects a pre-programmed channel, then sends an emergency signal to your Base Station. · The pre-programmed channel remains selected until a control signal is received from the Base Station, or power is turned OFF. · The emergency call is repeatedly transmitted at pre-programmed intervals. 14 PROGRAMMABLE FUNCTIONS 4 D DISPLAY LIGHTING The function display has 3 backlight conditions. AUTO : When any key, except [PTT], is pushed, the backlight turns ON for 5 sec. D SmarTrunk IITM functions This transceiver provides SmarTrunk IITM functions. (Optional UT-105 SmarTrunk II TM Logic Board is required. ) The optional UT-105 allows communication over conventional channels or SmarTrunk IITM channels. To toggle SmarTrunk IITM channels and conventional channels, push the [Bank] switch one or more times. · Scanning starts when a channel bank for SmarTrunk IITM is selected. 19 for more detailed operation. ) 15 5 CONVENTIONAL OPERATION ` Receiving and transmitting NOTE: Transmitting without an antenna may damage the transceiver. Receiving: q Push [CH Up]/[CH Down], or rotate the [SEL] to select a channel. w Listen for a transmission and adjust [VOL] to a comfortable listening level. · When no transmission is heard, push and hold monitor while adjusting [VOL] (your transceiver may not be programmed with the monitor function). The transceiver is now set to receive desired calls on the selected channel. Transmitting: Wait for the channel to become clear to avoid interference. e While pushing and holding [PTT], speak into the microphone at a normal voice level. · When a tone signalling system is used, the call procedure described at right may be necessary. r Release [PTT] to return to receive. IMPORTANT: To maximize the readability of your transmitted signal, pause a few seconds. (5 to 10 cm) from your mouth and speak at a normal voice level. 16 CONVENTIONAL OPERATION 5 ` Call procedure When your system employs tone signalling (excluding CTCSS and DTCS), the call procedure may be necessary prior to voice transmission. [. . . ] In order to use the above functions, cloning is necessary via a PC using the optional CS-F30G CLONING SOFTWARE. Using this software, the transceiver's model, individual RX Code CH, TX Code CH, Special Tone Link2 (must be `E') in 5Tone screen, 5Tone Signaling Form in Memory-CH screen, Log, RX C-No, Key&Display, Common Auto Reset Timer B, and other settings related to operation can be set. Refer to the HELP file that comes with the CS-F30G CLONING SOFTWARE for available settings. 22 OPTIONAL UNIT INSTALLATION TM 8 You can install two of the following optional units in the transceiver. UT-105 SmarTrunk II Logic Board, UT-109/UT-110 VOICE SCRAMBLER UNIT, UT-111 TRUNKING BOARD, UT-113 MAN DOWN UNIT. ` Installation q Unscrew nut a, and remove the knobs. [. . . ]


Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets...
In any way can't Lastmanuals be held responsible if the document you are looking for is not available, incomplete, in a different language than yours, or if the model or language do not match the description. Lastmanuals, for instance, does not offer a translation service.

Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual ICOM IC-F30GT-GS will begin.

Search for a user manual


Copyright © 2015 - LastManuals - All Rights Reserved.
Designated trademarks and brands are the property of their respective owners.