User manual ICOM IC-F3GT GS

[. . . ] NEVER short the terminals of the bat- EXPLICIT DEFINITIONS DEFINITION Personal injury, fire hazard or electric shock RWARNING may occur. CAUTION NOTE Equipment damage may occur. No risk of personal injury, fire or electric shock. WORD tery pack. DO NOT push PTT when not actually desiring to transmit. [. . . ] · Push [Side1] (MONI) to cancel the Ringer beep and " " blinks. · When no answer comes back, the transceiver emits short failure beep tones. While transmitting Communication Piro Piro 5 4 5 Push (S-Ring/Ringer) Answer back (automatic) Piro P iro Appears Appears e Push [PTT] to answer the call and to stop the beeps and blinking. NOTE: This function is available only when the called station has use the same CTCSS tone code and the same operating channels as you. 14 5 RINGER FUNCTION (Analog mode operation only) I Call-Ring operation q Set the same operating channel and CTCSS tone code for all of your group transceivers. w Push and hold (S-Ring/Ringer) to send the pre-selected ring tone to your group members. ·" " and " " appears. · The ring tone* is emitted while (S-Ring/Ringer) is pushed and held. · The same ring tone comes from your group station's speaker. While transmitting I Auto channel function The auto channel function automatically searches a clear channel during scan when (S-Ring/Ringer) is pushed. Then, the ringer tone is transmitted for a specified period in the founded clear channel. Another station during scanning may answer the call in the clear channel if it receives the ringer signal. 28) r Push [Side2] (CH Up) or [Side3] (CH Down) to select the desired tone code. t Push [Code] again to set. 16 6 TONE SQUELCH OPERATION (Analog mode operation only) D DTCS code setting This transceiver is equipped with 84 DTCS codes. DTCS operation provides communication with silent standby since you will only receive calls from group members using the same DTCS code number. w Push [Side2] (CH Up) or [Side3] (CH Down) to select the desired channel. e Push [Code] to enter the DTCS code selection mode. ·" " appears. to toggle the DTCS code and CTCSS tone selection mode. · "DT OFF" (or "DT T-00") is displayed in no tone setting channel. · Available DTCS code list No. A0 A1 A2 A3 A4 A5 A6 A7 A8 A9 F0 F1 F2 F3 F4 F5 F6 F7 F8 F9 Code 023 025 026 031 032 036 043 047 051 054 371 411 412 413 423 431 432 445 464 465 No. B0 B1 B2 B3 B4 B5 B6 B7 B8 B9 G0 G1 G2 G3 G4 G5 G6 G7 G8 G9 Code 065 071 072 073 074 114 115 116 125 131 466 503 506 516 532 546 565 606 612 624 No. C0 C1 C2 C3 C4 C5 C6 C7 C8 C9 H0 H1 H2 H3 H4 H5 H6 H7 H8 H9 Code 132 134 143 152 155 156 162 165 172 174 627 631 632 654 662 664 703 712 723 731 No. D0 D1 D2 D3 D4 D5 D6 D7 D8 D9 I0 I1 I2 I3 00 Code 205 223 226 243 244 245 251 261 263 265 732 734 743 754 OFF No. [. . . ] 17) 38 12 SPECIFICATIONS I Channel frequency lists (Continued) Channel 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 Zone 3 (Analog mode) Frequency (MHz)*1 446. 006250 446. 018750 446. 031250 446. 043750 446. 056250 446. 068750 446. 081250 446. 093750 Tone (Hz)*2 67. 0 71. 9 74. 4 77. 0 79. 7 82. 5 85. 4 88. 5 Zone 4 (Digital mode) Frequency (MHz)*1 446. 103125 446. 109375 446. 115625 446. 121875 446. 128125 446. 134375 446. 140625 446. 146875 446. 153125 446. 159375 446. 165625 446. 171875 446. 178125 446. 184375 446. 190625 446. 196875 Common ID*3 85 87 93 95 117 119 125 127 213 215 221 223 245 247 253 254 *1 All operating channel frequencies are fixed. *2 CTCSS tone frequencies can be programmed by manually. 16) You can use DTCS (Digital Tone Code Squelch) instead of CTCSS. 17) *3 Common ID can be programmed by manually. [. . . ]