User manual ICOM IC-F4029SDR

[. . . ] INSTRUCTION MANUAL UHF TRANSCEIVER iF4029SDR IMPORTANT READ ALL INSTRUCTIONS carefully and completely before using the transceiver. PRECAUTIONS R CAUTION!NEVER hold the transceiver so that the antenna is very close to, or touching exposed parts of the body, especially the face or eyes, while transmitting. The transceiver will perform best if the microphone is 5 to 10 cm away from the lips and the transceiver is vertical. SAVE THIS INSTRUCTION MANUAL -- This instruction manual contains important operating instructions for the IC-F4029SDR UHF TRANSCEIVER. R CAUTION!NEVER operate the transceiver with a headset or other audio accessories at high volume levels. R CAUTION! [. . . ] Another station during scanning may answer the call in the clear channel if it receives the ringer signal. q Push [Auto Ch] to start scan. · The selected scan type and scan list are available. 10, 12) w To call a waiting station, push sec. to transmit a ringer tone. (S-Ring/Ringer) for 1 Appears Appears · The auto channel function automatically searches a clear channel. After a clear channel found, a ringer tone is transmitted. · To call a waiting station by voice, push [PTT] until beep tones sound (for longer than the ringer time), then speak into the microphone. * The Call-Ring emission type can be selected in Set mode. 27) e The auto channel function restarts 30 sec. later after a busy signal disappears and in which no operation is performed while the auto channel function is in use. r Push [Auto Ch] to cancel the function. 15 TONE SQUELCH OPERATION (Analog mode operation only) ` Operation By default, the transceiver uses a CTCSS/DTCS squelch system. DTCS opens only when receiving a signal containing a matching tone. You can silently wait for calls from group members using the same tone. 6 y When the received signal includes a matching tone, squelch opens and the signal can be heard. · When the received signal's tone does not match, tone squelch does not open. · To open the squelch temporarily, push [Side1] (MONI). D CTCSS tone setting The transceiver is equipped with 50 CTCSS tones. CTCSS operation provides communication with silent standby since you will only receive calls from group members using the same CTCSS tone frequency. w Push [Side2] (CH Up) or [Side3] (CH Down) to select the desired channel. 38, 39) e Push [Code] to enter the CTCSS tone frequency selection mode. ·" " appears. to toggle the CTCSS tone and DTCS code selection mode. · "CT OFF" (or "CT T-00") is displayed in no tone setting channel. · Available CTCSS tone frequency No. 67. 0 69. 3 71. 9 74. 4 77. 0 79. 7 82. 5 85. 4 88. 5 91. 5 No. 94. 8 97. 4 100. 0 103. 5 107. 2 110. 9 114. 8 118. 8 123. 0 127. 3 No. 131. 8 136. 5 141. 3 146. 2 151. 4 156. 7 159. 8 162. 2 165. 5 167. 9 No. 171. 3 173. 8 177. 3 179. 9 183. 5 186. 2 189. 9 192. 8 196. 6 199. 5 No. 41 42 43 44 45 46 47 48 49 50 00 (Hz) Freq. [. . . ] 19) 39 OPTIONS D BATTERY PACK Battery pack BP-231 BP-232 BP-240 1 13 D BELT CLIPS Capacity 1150 mAh 2000 mAh Battery life*1 Analog mode Digital mode Analog mode Digital mode 10. 4 hrs. 14 hrs. Voltage 7. 4 V 7. 4 V · MB-93 SWIVEL BELT CLIP · MB-94 BELT CLIP The same as supplied with the transceiver. · MB-96N/96F LEATHER BELT HANGER Battery case for AAA (LR03) × 6 alkaline D DC CABLES · CP-17L CIGARETTE LIGHTER CABLE Allows charging of the battery pack through a 12 V cigarette lighter socket. (For BC-119N) · OPC-515L/OPC-656 DC POWER CABLES Allows charging of the battery pack using a 13. 8 V power source instead of the AC adapter. [. . . ]