User manual ICOM IC-F40GT-GS

[. . . ] INSTRUCTION MANUAL VHF TRANSCEIVER UHF TRANSCEIVER iF30GT/GS iF40GT/GS This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must except any interference received, including interference that may cause undesired operation. FOREWORD Thank you for purchasing the IC-F30GT/GS, IC-F40GT/GS FM transceiver. READ ALL INSTRUCTIONS carefully and completely before using the transceiver. SAVE THIS INSTRUCTION MANUAL­This instruction manual contains important operating instructions for the transceiver. INSTALLATION NOTES · When transmitting with a portable radio, hold the radio in a vertical position with its microphone 2. 5 to 5 centimeters (1 to 2 in. ) away from your mouth. [. . . ] If you want to charge the battery pack more than 300 times, the following points should be observed: · Avoid over charging. The charging period should be less than 48 hours. · Use the battery until it becomes almost completely exhausted under normal conditions. We recommend battery charging after transmitting becomes impossible. 1020 (4 groups × 255) code numbers are available. Push the [Scrambler] switch to toggle the function ON and OFF. NOTE: NEVER use #01 Low AF level versions, as they are not compatible 12 PROGRAMMABLE FUNCTIONS 4 D MONITOR AUDIBLE FUNCTION The monitor function allows you to open the transceiver's squelch manually to check whether a channel is busy or not. The transceiver has 2 conditions for receive standby: Audible condition: This condition mutes audio ONLY when no carrier is present. You can receive (or monitor) any signals on a channel. · Push and hold the [Moni] (LMR) or [Moni (Audi)] (PMR) switch to select the audible condition. while pushing the [Moni] (LMR) or Any audio mute functions are cancelled [Moni (Audi)] (PMR) switch. Inaudible condition: This condition mutes ALL signals except those directed to you. Therefore you should check a channel's condition (busy or not) with the monitor function before transmitting. Only signals containing the · Push the [Moni] (LMR) or [Moni (Audi)] proper tone are received. (PMR) switch momentarily to select the inaudible condition. D TALK AROUND The talk around function changes duplex channels to simplex channels. · Duplex allows you to contact your base station, repeaters, etc. · Simplex allows you to contact other portable transceivers directly (portable-to-portable contact). Push the [Talk Around] switch to toggle the function ON and OFF. 13 4 PROGRAMMABLE FUNCTIONS D DTMF TRANSMISSION This function allows you to send a pre-programmed DTMF code to control a repeater, open another transceiver's squelch, etc. Manual transmission: Push the desired digit keys in sequence while pushing [PTT]. · Pushing [PTT] may not be necessary depending on programming. Automatic pre-programmed transmission: q Push the [DTMF Autodial] switch to select DTMF autodial mode, then push [CH Up] or [CH Down] to select the desired channel. w Push the [DTMF Autodial] switch to send a DTMF code. D DTMF RE-DIAL FUNCTION This function allows you to transmit the last-used DTMF code at the push of a key. Push the [Re-dial] switch momentarily to activate the function. · The previously transmitted DTMF code is automatically transmitted. · If no code has been transmitted since turning the power ON, this function does not activate. D EMERGENCY FUNCTION The emergency function allows you to send an emergency signal quickly and easily to your Base Station, etc. Push and hold the [Emergency Single/Repeat] switch for 1 sec. to activate the emergency function. · The transceiver selects a pre-programmed channel, then sends an emergency signal to your Base Station. · The pre-programmed channel remains selected until a control signal is received from the Base Station, or power is turned OFF. [. . . ] r Unscrew 2 screws e then separate the chassis from the front panel in the direction of the arrow. Be careful!: A flat cable is connected between the MAIN unit on the chassis and front panel. c e a d d b t Install the desired optional unit. NOTE: When installing UT-105 or UT-111, the unit MUST BE plugged into SLOT 1. Otherwise the unit will not working correctly. (Other optional units can be plugged into either slot. ) Slot 2 Slot 1 y Program the necessary information with the cloning software before operation. [. . . ]