User manual ICOM IC-F41GT

Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets... DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!

Sponsored Links

If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Lastmanuals provides you a fast and easy access to the user manual ICOM IC-F41GT. We hope that this ICOM IC-F41GT user guide will be useful to you.

Lastmanuals help download the user guide ICOM IC-F41GT.


ICOM IC-F41GT : Download the complete user guide (489 Ko)

You may also download the following manuals related to this product:

   ICOM IC-F41GT BROCHURE (2243 ko)

Manual abstract: user guide ICOM IC-F41GT

Detailed instructions for use are in the User's Guide.

[. . . ] INSTRUCTION MANUAL VHF TRANSCEIVER UHF TRANSCEIVER iF31GT/GS iF41GT/GS FOREWORD Thank you for purchasing the IC-F31GT/GS, IC-F41GT/GS FM transceiver. READ ALL INSTRUCTIONS carefully and completely before using the transceiver. SAVE THIS INSTRUCTION MANUAL­This instruction manual contains important operating instructions for the transceiver. ABOUT CE CE Versions of the IC-F31GT/GS, ICF41GT/GS which display the "CE" symbol on the serial number seal, comply with the essential requirements of the European Radio and Telecommunication Terminal Directive 1999/5/EC. This warning symbol indicates that this equipment operates in nonharmonised frequency bands and/or may be subject to licensing conditions in the country of use. [. . . ] ily to select the inaudible condition. D TALK AROUND The talk around function changes duplex channels to simplex channels. · Duplex allows you to contact your base station, repeaters, etc. · Simplex allows you to contact other portable transceivers directly (portable-to-portable contact). Push the [Talk Around] switch to toggle the function ON and OFF. 13 4 PROGRAMMABLE FUNCTIONS D DTMF TRANSMISSION This function allows you to send a pre-programmed DTMF code to control a repeater, open another transceiver's squelch, etc. Manual transmission: Push desired digit keys in sequence while pushing [PTT]. · Pushing [PTT] may not be necessary depending on programming. Automatic pre-programmed transmission: q Push the [DTMF Autodial] switch to select DTMF autodial mode, then push [CH Up] or [CH Down] to select the desired channel. D DTMF RE-DIAL FUNCTION This function allows you to transmit the last-used DTMF code at the push of a key. Push the [Re-dial] switch momentarily to activate the function. · The previously transmitted DTMF code is automatically transmitted. · If no code has been transmitted since turning the power ON, this function does not activate. D EMERGENCY FUNCTION The emergency function allows you to send an emergency signal quickly and easily to your Base Station, etc. to activate the emergency function. · The transceiver selects a pre-programmed channel, then sends an emergency signal to your Base Station. · The pre-programmed channel remains selected until a control signal is received from the Base Station, or power is turned OFF. · The emergency call is repeatedly transmitted at pre-programmed intervals. 14 PROGRAMMABLE FUNCTIONS 4 D DISPLAY LIGHTING The function display has 3 backlight conditions. D SmarTrunk IITM functions This transceiver provides SmarTrunk IITM functions. (Optional UT-105 SmarTrunk II TM Logic Board is required. ) The optional UT-105 allows communication over conventional channels or SmarTrunk IITM channels. To toggle SmarTrunk IITM channels and conventional channels, push the [Bank] switch one or more times. · Scanning starts when a channel bank for SmarTrunk IITM is selected. 21 for more detailed operation. ) 15 5 CONVENTIONAL OPERATION ` Receiving and transmitting NOTE: Transmitting without an antenna may damage the transceiver. Receiving: q Push [CH Up]/[CH Down], or rotate [SEL] to select a channel. w Listen for a transmission and adjust [VOL] to a comfortable listening level. · When no transmission is heard, push and hold monitor while adjusting [VOL] (your transceiver may not be programmed with the monitor function). The transceiver is now set to receive desired calls on the selected channel. Transmitting: Wait for the channel to become clear to avoid interference. e While pushing and holding [PTT], speak into the microphone at a normal voice level. · When a tone signalling system is used, the call procedure described at right may be necessary. r Release [PTT] to return to receive. IMPORTANT: To maximize the readability of your transmitted signal, pause a few seconds. After pushing [PTT], hold the microphone 5 to 10 cm from your mouth and speak at a normal voice level. 16 CONVENTIONAL OPERATION 5 ` Call procedure When your system employs tone signalling (excluding CTCSS and DTCS), the call procedure may be necessary prior to voice transmission. The tone signalling employed may be a selective calling system which allows you to call specific station(s) only and prevent unwanted stations from contacting you. q Select the desired Tx code channel or 5-tone code according to your System Operator's instructions. · This may not be necessary depending on programming. · Refer to the next page for selection. w Push the call switch (assigned to one of the dealer programmable switches: [P0], [P1], [P2], [P3], [F2] and [F3]). e After transmitting a 5-tone code, the remainder of your communication can be carried out in the normal fashion. Selective calling Non-selective calling 17 5 CONVENTIONAL OPERATION ` Tx code channel selection Your radio may be programmed for Tx code channel selection. [. . . ] r Unscrew 2 screws e, then take off the chassis from the front panel in the direction of the arrow. Be careful!: Flat cable is connected between the MAIN unit on the chassis and front panel. c e a d d b t Install the desired optional unit. NOTE: When installing UT-105 or UT-111, the unit MUST BE pluged into SLOT 1. (Other optional units can be plugged into either slot. ) Slot 2 Slot 1 y Program the necessary information with the cloning software before operation. Please ask your dealer or system operator for details. 23 9 CLONING ` Cloning Cloning allows you to quickly and easily transfer the programmed contents from one transceiver to another transceiver; or data from PC to a transceiver using the optional CS-F30G CLONING SOFTWARE. [. . . ]

DISCLAIMER TO DOWNLOAD THE USER GUIDE ICOM IC-F41GT

Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets...
In any way can't Lastmanuals be held responsible if the document you are looking for is not available, incomplete, in a different language than yours, or if the model or language do not match the description. Lastmanuals, for instance, does not offer a translation service.

Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual ICOM IC-F41GT will begin.

Search for a user manual

 

Copyright © 2015 - LastManuals - All Rights Reserved.
Designated trademarks and brands are the property of their respective owners.

flag