User manual ICOM IC-F50
Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets... DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!
If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Lastmanuals provides you a fast and easy access to the user manual ICOM IC-F50. We hope that this ICOM IC-F50 user guide will be useful to you.
Lastmanuals help download the user guide ICOM IC-F50.
You may also download the following manuals related to this product:
ICOM IC-F50 annexe 1 (807 ko)
ICOM IC-F50 Instruction Manual (1040 ko)
Manual abstract: user guide ICOM IC-F50
Detailed instructions for use are in the User's Guide.
[. . . ] INSTRUCTION MANUAL
This device complies with Part 15 of the FCC rules. Operation is subject to the condition that this device does not cause harmful interference.
SAFETY TRAINING INFORMATION
Your Icom radio generates RF electromagnetic energy during transmit mode. This radio is designed for and classified as "Occupational Use Only", meaning it must be used only during the course of employment by individuals aware of the hazards, and the ways to minimize such hazW ARN ING ards. This radio is NOT intended for use by the "General Population" in an uncontrolled environment. [. . . ] When a received SDM is displayed, push to cancel the automatic scroll and scroll the message manually. When an SDM that contains more than 8 characters is displayed, push to scroll the message manually.
I Turning power ON
q Rotate [VOL] to turn power ON. w If the transceiver is programmed for a start up passcode, input digit codes as directed by your dealer.
· The keys in the table below can be used for password input: · The transceiver detects numbers in the same block as identical. Therefore "01234" and "56789" are the same.
KEY NUMBER 0 5 1 6 2 7 3 8 4 9
e When the "PASSWORD" indication does not clear after inputting 4 digits, the input code number may be incorrect. Turn the power off and start over in this case.
I Channel selection
Several types of channel selections are available. NON-BANK TYPE: Push [ ]/[ ] to select the desired operating channel, in sequence; or, push one of the [MR-CH 1] to [MR-CH 4] keys to select a channel directly. BANK-TYPE: Push [Bank], then push [ ] or [ ] to select the desired bank.
AUTOMATIC SCAN TYPE: Channel setting is not necessary for this type. When turning the power ON, the transceiver automatically starts scanning. Scanning stops when receiving a call.
I Call procedure
When your system employs tone signalling (excluding CTCSS and DTCS), the call procedure may be necessary prior to voice transmission. The tone signalling employed may be a selective calling system which allows you to call specific station(s) only and prevent unwanted stations from contacting you. q Select the desired TX code channel or 2/5-tone code according to your System Operator's instructions.
· This may not be necessary depending on programming. 15, 16 for selection.
w Push the call switch (assigned to one of the dealer programmable switches: [P0], [P1], [P2], [P3], [Red], [ ] and [ ]). e After transmitting a 2/5-tone code, the remainder of your communication can be carried out in the normal fashion.
Selective calling Non-selective calling
I Receiving and transmitting
NOTE: Transmitting without an antenna may damage the transceiver. 1 for antenna attachment.
q Rotate [VOL] to turn power ON. e When receiving a call, adjust the audio output level to a comfortable listening level.
Wait for the channel to become clear to avoid interference. q While pushing and holding [PTT], speak into the microphone at a normal voice level.
· When a tone signalling system is used, the call procedure described at left may be necessary.
w Release [PTT] to return to receive. Hold the microphone 5 to 10 cm (2 to 4 inches) from your mouth, then speak into the microphone at a normal voice level.
D Transmitting notes
· Transmit inhibit function The transceiver has several inhibit functions which restrict transmission under the following conditions: - The channel is in mute condition (`Inaudible' condition; " " does not appear). · Time-out timer After continuous transmission for the pre-programmed time period, the time-out timer is activated, causing the transceiver to stop transmitting. · Penalty timer Once the time-out timer is activated, transmission is further inhibited for a period determined by the penalty timer.
D TX code channel selection
If the transceiver has [TX Code CH Select] assigned to it, indication can be toggled between the operating channel number (or name) and TX code channel number (or name). When the TX code channel number (or name) is displayed, the [ ]/[ ] key selects the TX code channel. TO SELECT A TX CHANNEL: q Push [TX Code CH Select]-- a TX code channel appears. e Push [Call] (or [PTT] during MSK operation) to transmit the selected TX code. [. . . ] Charge indicator lights green while charging.
Supplied screws BC-152 AC adapter 37
D For your convenience
Eyelet USE a rubber band to secure the transceiver while charging, if desired.
ï AD-100 installation
q Install the AD-100 desktop charger adapter into the holder space of the BC-119N/121N.
Desktop charger adapter
w Connect the plugs of the BC-119N/121N to the AD-100 with the connector, then install the adapter into the charger with the supplied screws.
Screws supplied with the charger adapter
D Rapid charging with the BC-119N+AD-100
The optional BC-119N provides rapid charging of optional Li-Ion battery packs. The followings are additionally required: · One AD-100 (purchase separately). · An AC adapter (may be supplied with BC-119N depending on version) or the DC power cable (OPC-515L/CP-17L).
Transceiver Battery pack Turn power OFF
AC adapter (Not supplied with some versions. )
AD-100 charger adapter is installed in BC-119N.
Optional OPC-515L (for 13. 8 V power source) or CP-17L (for 12 V cigarette lighter socket) can be used instead of the AC adapter.
D Rapid charging with the BC-121N+AD-100
The optional BC-121N allows up to 6 battery packs to be charged simultaneously. · An AC adapter (BC-157) or the DC power cable (OPC-656)
Transceiver Turn power OFF Battery pack AC adapter (Purchase separately. )
AD-100 charger adapters are installed in each slot.
ER HARG TI-C MUL
DC power cable (OPC-656) (Connect with the DC power supply; 13. 8 V/at least 7 A)
I Optional battery case
When using the optional battery case, install 5 × AA (R6) size alkaline batteries as illustrated at right. [. . . ]
DISCLAIMER TO DOWNLOAD THE USER GUIDE ICOM IC-F50
Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets...
In any way can't Lastmanuals be held responsible if the document you are looking for is not available, incomplete, in a different language than yours, or if the model or language do not match the description. Lastmanuals, for instance, does not offer a translation service.
Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual ICOM IC-F50 will begin.