User manual ICOM IC-F5022

[. . . ] INSTRUCTION MANUAL VHF MOBILE TRANSCEIVER UHF MOBILE TRANSCEIVER iF5022 iF6022 IMPORTANT READ ALL INSTRUCTIONS carefully and completely before usng the transcever. EXPLICIT DEFINITIONS WORD RWARNING CAUTION NOTE DEFINITION Personal njury, fre hazard or electrc shock may occur. No rsk of personal njury, fire or electrc shock. SAVE THIS INSTRUCTION MANUAL -- Ths nstructon manual contans mportant operatng nstructons for the IC-F5022 VHF MOBILE TRANSCEIVER and the IC-F6022 UHF MOBILE TRANSCEIVER. Icom, Icom Inc. and the Icom logo are regstered trademarks of Icom Incorporated (Japan) n Japan, the Unted States, the Unted Kngdom, Germany, France, Span, Russa and/or other countres. All other products or brands are regstered trademarks or trademarks of ther respectve holders. PRECAUTIONS RWARNING! [. . . ] When turnng power ON, the transcever automatcally starts scannng. Scannng stops when recevng a call. KEY NUMBER 0 5 1 6 2 7 3 8 4 9 e When the "PASSWORD" ndcaton does not clear after nputtng 4 dgts, the nput code number may be ncorrect. Turn the power off and start over n ths case. 7 2 BASIC OPERATION Call procedure When your system employs tone sgnalng (excludng CTCSS and DTCS), a call procedure may be necessary pror to voce transmsson. The tone sgnallng employed may be a selectve callng system whch allows you to call specfic staton(s) only and prevents unwanted statons from contactng you. q Select the desred TX code channel, 2/5-tone code accordng to your System Operator's nstructons. · Ths may not be necessary dependng on programmng. · Refer to pages 9­10 for selecton. Receiving and transmitting Receiving: q Push and hold [ ] for 1 sec. w Push [CH Up] or [CH Down] to select a channel, n sequence. e When recevng a call, rotate [VOL] to adjust the audo output level to a comfortable lstenng level. NOTE: Dependng on the pre-settng, the transcever automatcally transmts the mcrophone audo for the specfied tme perod* when a matched RX code sgnal s receved. · HM-148G or HM-152 hand microphone s requred. Ask your dealer for detals. w Push [Call] (assgned to one of the dealer programmable keys). e After transmttng, the remander of your communcaton can be carred out n the normal fashon. Selective calling Non-selective calling Transmitting: Wat for the channel to become clear to avod nterference. q Take the mcrophone off hook. · The `audble' condton s selected. · A prorty channel may be selected automatcally. w Wat for the channel to become clear. · The channel s busy when BUSY ndcator appears on the LCD. e Whle pushng and holdng [PTT], speak nto the mcrophone at your normal voce level. IM. ORTANT: To maxmze the readablty of your sgnal; 1. Hold the mcrophone 5 to 10 cm (2 to 4 nches) from your mouth, then speak nto the mcrophone at a normal voce level. 8 BASIC OPERATION D Transmitting notes D TX code channel selection 2 1. 1. 2 1. 3 1. 4 1. 5 1. 6 · Transmit inhibit function The transcever has several nhbt functons whch restrct transmsson under the followng condtons: - The channel s n mute condton (`Inaudble' condton; " " (Audble ndcator) does not appear. ) - The channel s busy. - Un-matched (or matched) CTCSS s receved. (Dependng on the pre-settng) If the transcever has [TX Code CH Select] assgned to t, the ndcaton can be toggled between the operatng channel number (or name) and TX code channel number (or name). When the TX code channel number (or name) s dsplayed, [CH Up] or [CH Down] selects the TX code channel. USING [TX CODE CH SELECT] KEY: q Push [TX Code CH Select]-- a TX code channel number (or name) appears. w Push [CH Up] or [CH Down] to select the desred TX code channel. e After selectng, push [TX Code CH Select] to set. · Return to the stand-by mode. - The selected channel s a `receve only' channel. · Time-out timer After contnuous transmsson for the pre-programmed tme perod, the tme-out tmer s actvated, causng the transcever to stop transmttng. [. . . ] Crmp Solder CONNECTION AND MAINTENANCE 3 1. 1. 2 1. 3 1. 4 1. 5 1. 6 Supplied Accessories Microphone Microphone hanger and screw set Microphone hanger cable Mounting the transceiver The unversal mountng bracket suppled wth your transcever allows overhead mountng. · Mount the transcever securely wth the 4 suppled screws to a thck surface whch can support more than 1. 5 kg. Flat washer DC power cable Function name stickers* Mounting bracket Felt* Spring washer Flat washers Nuts Mounting screws (M5×12) Spring washers Bracket bolts Self-tapping screws (M5×20) Felt* When using self-tapping screws *Felts reduce the vibration effects. * Used for labelling the programmable function keys according to their assinged functions. 15 3 CONNECTION AND MAINTENANCE Antenna A key element n the performance of any communcaton systems s an antenna. Contact your dealer for more nformaton regardng antennas and how to nstall them. Options · O. C-1. 1. 32A/O. C-347 dc power cable 2 fuse holders are attached. [. . . ]