User manual ICOM IC-F6062

[. . . ] INSTRUCTION MANUAL iF5062 UHF MOBILE TRANSCEIVER VHF MOBILE TRANSCEIVER iF6062 IMPORTANT READ ALL INSTRUCTIONS carefully and completely before using the transceiver. PRECAUTIONS RWARNING!NEVER connect the transceiver to an AC outlet. This may pose a fire hazard or result in an electric shock. NEVER connect the transceiver to a power source of more than 16 V DC such as a 24 V battery. [. . . ] · Push to mute the channel (sets to `Inaudible' only). · Push to un-mute the channel (sets to `Audible' only). · Push after the communication is finished to send a `reset code'. (BIIS PMR operation only) 1 1 PUBLIC ADDRESS KEY Push to activate the Public Address (PA) function for voice amplification. When the PA function is activated, the audio output can be controlled from the transceiver separately with the [VOL] control knob. · This function is available when the external unit, such as a audio amplifier, speaker, etc. · Push this key, then speak into the microphone while pushing and holding [PTT]. · [CH Up]/[CH Down] also allow you to set the audio output level. RX SPEAKER KEY The received audio can be heard via the external speaker when this key is pushed. · This function is available when the external speaker is additionally connected. · This function is useful when you are out of the vehicle. · The audio output level is linked to the transceiver's volume control. NOTE: The un-mute condition (`Audible' condition) may automatically return to the mute condition (`Inaudible' condition) after a specified period depending on programming. LIGHT KEY Push to turn the transceiver's backlight ON for about 5 sec. when the backlight function is turned OFF in user set mode. LOCK KEY Push and hold to electronically lock all programmable keys except the following: [Moni(Audi)], [Light], [Lock], [Call] (incl. Call A and Call B), [Emergency Single]/[Emergency Repeat] (incl. Silent), [Surveillance] and [OPT 1/2/3]. 4 1 PANEL DESCRIPTION SCRAMBLER FUNCTION Push to toggle the voice scrambler function ON and OFF. COMPANDER KEY Push to toggle the compander function ON and OFF. The compander function reduces noise components from the transmitted audio to provide clear communication. 5 PANEL DESCRIPTION TX CODE ENTER KEY (PMR or BIIS PMR operation only) Push to enter the ID code edit mode directly, for both 5-tone and MSK. Then set the desired digit using [CH Up]/ [CH Down]. 10) TX CODE CHANNEL SELECT KEY Push to enter the ID code channel selection mode directly. Then set the desired channel using [CH Up]/[CH Down]. 9) During ID code channel selection mode, push for 1 sec. to enter the ID code edit mode for 5-tone and MSK. Then set the desired digit using [CH Up]/[CH Down]. 10) TX CODE CHANNEL UP/DOWN KEYS Push to select a TX code channel directly. [. . . ] 1) t IGNITION LEAD Connects to a ignition line. Binding to the DC power cable is recommended. 12V Battery 13 R CAUTION!NEVER remove the fuse-holder from the DC power cable. CONNECTION AND MAINTENANCE 3 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 I Supplied Accessories Microphone Microphone hanger and screw set Microphone hanger cable I Mounting the transceiver The universal mounting bracket supplied with your transceiver allows overhead mounting. · Mount the transceiver securely with the 4 supplied screws to a thick surface which can support more than 1. 5 kg. DC power cable Function name stickers*1 Sponges*2 Flat washer Felt* Spring washer Mounting bracket and felts Flat washers Spring washers Nuts Bracket bolts Mounting screws (M5×12) Felt* When using self-tapping screws *Felts reduce the vibration effects. Felts are already attached. Self-tapping screws (M5×16) *1 Used for labelling the programmable function keys according to their assinged functions. [. . . ]