User manual ICOM IC-F61M

[. . . ] INSTRUCTION MANUAL UHF MARINE TRANSCEIVER iF61M FOREWORD Thank you for purchasng ths Icom transcever. The IC-F61M uhf marine transceiver s desgned and bult wth Icom's state of the art technology and craftsmanshp. Wth proper care ths product should provde you wth years of trouble-free operaton. IMPORTANT READ ALL INSTRUCTIONS carefully and completely before usng the transcever. SAVE THIS INSTRUCTION MANUAL-- Ths nstructon manual contans mportant operatng nstructons for the IC-F61M uhf marine transceiver. EXPLICIT DEFINITIONS WORD DEFINITION Personal injury, fire hazard or electric shock may occur. No risk of personal injury, fire or electric shock. RWARNING CAUTION NOTE RECOMMENDATION CLEAN THE TRANSCEIVER THOROUGHLY WITH FRESH WATER after exposure to saltwater, and dry t before operaton. [. . . ] USING [TX CODE CH SELECT] KEY: q Push [TX Code CH Select] to enter the TX code channel selecton mode. · Select the desred operatng channel before enterng the TX code channel selecton mode f necessary. w Push [TX Code CH Select] for 1 sec. to enter the TX code edt mode. · The dgt to be edted blnks. 17 BASIC OPERATION 3 e Push [TX Code CH Select] to select the desred dgt to be edted. r Push [CH Up]/[CH Down] to select the desred dgt. The dgt to the rght wll blnk automatcally. y Repeat r and t to edt all allowable dgts. u After edtng, push [TX Code CH Select] to set. · Return to the stand-by mode. 3 i Push [Call] to transmt. USING [TX CODE ENTER] KEY: q After pushng [TX Code CH Select], push [CH Up]/[CH Down], or push [TX Code CH Up]/[TX Code CH Down] to select the desred TX code channel. w Push [TX Code Enter] to enter the TX code edt mode. · The dgt to be edted blnks. e Push [TX Code Enter] to select the desred dgt to be edted. r Push [CH Up]/[CH Down] to select the desred dgt. The dgt to the rght wll blnk automatcally. y Repeat r and t to edt all allowable dgts. u After edtng, push [TX Code Enter] to set. · Return to the stand-by mode. i Push [Call] to transmt. D DTMF transmission If the transcever has [DTMF Autodal] assgned to t, the automatc DTMF transmsson functon s avalable. q Push [DTMF Autodal]-- a DTMF channel appears. w Push [CH Up]/[CH Down] to select the desred DTMF channel. e Push [DTMF Autodal] to transmt the DTMF code to the selected DTMF channel. 18 3 BASIC OPERATION User set mode User set mode s accessed at power ON and allows you to set seldom-changed settngs. You can "customze" the transcever operaton to sut your preferences and operatng style. Entering the user set mode: q Whle pushng and holdng [ power ON. · Turn power OFF n advance. · "SET MODE" appears for 1 sec. ] and [ ], rotate [VOL] to w Push and hold [P0] for 1 sec. e Push [P0] momentarly to select the approprate tem. Then push [ ]/[ ] to set the desred level/condton. · Avalable set mode functons are Backlight, Beep, SQL Level, Ringer Level, AF Min level, Mic Gain, VOX Gain*, VOX Delay*, Battery Voltage, Signal Moni, Vibration and Lone Worker. r Push and hold [P0] agan to ext set mode. *Appears when the optonal headset s connected. User set mode s also avalable usng a programmable key. 12 [User Set Mode] secton for nstructons regardng usng the key assgned for user set mode. [. . . ] Push [High/Low] key to select hgh power (p. <Problem> The displayed channel cannot be changed. <Soluton> · Lock functon s actvated. Push and hold [LOCK] key to cancel the functon (p. [. . . ]