User manual ICOM IC-F7000

[. . . ] INSTRUCTION MANUAL HF TRANSCEIVER iF7000 FOREWORD Thank you for purchasing this Icom product. The ICF7000 HF TRANSCEIVER is designed and built with Icom's superior technology and craftsmanship. With proper care, this product should provide you with years of trouble-free operation. We want to take a couple of moments of your time to thank you for making the IC-F7000 your radio of choice, and hope you agree with Icom's philosophy of "technology first. " Many hours of research and development went into the design of your IC-F7000. IMPORTANT READ THIS INSTRUCTION MANUAL CAREFULLY before attempting to operate the transceiver. SAVE THIS INSTRUCTION MANUAL. [. . . ] · Preparation for Status call Sending a Selective Beacon call on several Selcall channels, and check the propagation on each channel to select the channel of good signal quality. 20) · Sending Status call q Push [] or [] to select the desired channel for Selcall. SELCALL USB-A RX--3. 200. 0 12:34 HI C t Push [CALL] for 1 sec. to transmit the Status call. · Before transmitting the Status call, verify `SelfID' for your own ID. · While calling, push [CALL] to cancel the call. y After the Status call, your calling station responds a status information for an acknowledgement. Push [ CLR] or [OK ] to select the call, the following indication is displayed. MES. 20-01--------12:36 Status-ack--------1024 DCV:13. 5--SIG:-8. 0 TXP:-8. 0--SWR:-1. 5---å è-ID:2999 · Status information includes power supply voltage, signal strength, output power and VSWR. w Push [CALL] momentarily to enter the Call menu. --2020:SELCALL --TX:-3. 200. 0 --SelfID:1004 ç-SELCALL------------å è-ID:1024 e Push [ CLR] or [OK ] to select `STATUS CALL. ' · `SELCALL, ' `GPS BCON, ' `GPS POSN, ' `EMER SELCALL, ' `PAGECALL, ' `STATUS CALL, ' `SEL BCON' are selectable. --2020:SELCALL --TX:-3. 200. 0 --SelfID:1004 ç-STATUS-CALL--------å è-ID:1024 · Receiving Status call When a transceiver receives a Status call with your individual ID, it automatically responds by transmitting. The receiving Status Call is stored in the selcall memory. After receiving a Status call and push [ CLR] or [OK ] to select the call, the following indication is displayed. MES. 20-01--------12:34 Status-call-------1006 è-ID:2999 r Push [] to select `ID, ' then select an intended ID. · Last selected ID is displayed. · Enter the 4-digits (or 6-digits depending on Initial set mode setting) number of the desired ID using 10-keypad directly. Or push [OK ] to enter ID selection, push []/[] to select the pre-programmed ID, then push [OK ] to fix the ID. --2020:SELCALL --TX:-3. 200. 0 --SelfID:1004--------å ç-STATUS-CALL---è-ID:1024------------å 25 SELCALL/ALE OPERATION 4 ï TEL call Allows you to make a telephone call through a telephone interconnect service provider. · Preparation for TEL call Sending a Selective Beacon call on several TEL call channels, and check the propagation on each channel to select the channel of good signal quality. 20) · Sending TEL call q Push [] or [] to select the desired channel for TEL call. RADTEL USB-A RX--3. 760. 0 12:34 HI t Verify `SelfID' for your own ID. y Push [] to select `TEL. ' ----12:RADTEL --SelfID:1234 --ID:2999 ç-TEL:06011223355--------------è-----ICOM-BRANOFFCE2 u Push [OK ] to enter TEL number selection. · Push []/[] to select the pre-programmed TEL number, then push [OK ] to fix the number. ---01101601970 ç-ICOM-BRANOFFCE2----å ç-01200701997--------å è-00501702000 w Push [CALL] momentarily to enter the Call menu. ----12:RADTEL --TX:-3. 760. 0 --SelfID:1234 ç-TELCALL------------å è-ID:2999 C i Push [CALL] for 1 sec. to transmit TEL call. · While calling, push [CALL] to cancel the call. e Push [ CLR] or [OK ] to select `TELCALL. ' · `TELCALL, ' `TEL-DISCONNECT, ' `SEL BCON, ' `SELCALL' are selectable. ----12:RADTEL --TX:-3. 760. 0 --SelfID:1234 ç-TELCALL------------å è-ID:2999 · After TEL call C q After telephone call is finished, push [CALL] momentarily to enter the Call menu. w Push [] or [] to select the call selection, then push [ CLR] or [OK ] to select `TEL-DISCONNECT. ' · While connecting the TEL call, `TEL-DISCONNECT' appears automatically as first selection call. ----12:RADTEL --TX:-3. 760. 0 --SelfID:1234 ç-TEL-DISCONNECT-----å è-ID:2999 4 r Push [] to select `ID, ' then select an intended ID. · Last selected ID is displayed. · Enter the 4-digits (or 6-digits depending on Initial set mode setting) number of the intended ID using 10-keypad directly. Or push [OK ] to enter ID selection, push []/[] to select the pre-programmed ID, then push [OK ] to fix the ID. ----12:RADTEL --TX:-3. 760. 0 --SelfID:1234 ç-TELCALL------------å è-ID:2999 C e Push [CALL] for 1 sec. to transmit the disconnect call. · Until `TEL-DISCONNECT' is transmitted, the telephone interconnect service provider counts the time for charging. Convenient: Disconnecting the TEL call C Just push [CALL] for 1 sec. to transmit the disconnect call, when connecting the TEL call, The transceiver automatically selects `TEL-DISCONNECT` from the call selection while connecting the TEL call. 26 4 SELCALL/ALE OPERATION ï Emergency selcall The Emergency call allows you to broadcast an emergency signal with own position information. · Preparation for Emergency selcall Sending a Selective Beacon call on several Selcall channels, and check the propagation on each channel to select the channel of good signal quality. 20) · Sending Emergency selcall q Push [] or [] to select the desired channel for Emergency selcall. SELCALL USB-A RX--3. 200. 0 12:34 HI · Other than AUS version E q Push [EMG] momentarily to enter the Emergency Call channel group. [EMG] []/[] w Push [] or [] to select the channel. EMERGENCY CALL -*2010-EMER1---------å -*2060-EMER2 ç*2070-EMER3----å è-- w Push [CALL] momentarily to enter the Call menu. --2020:SELCALL --TX:-3. 200. 0 --SelfID:1004 ç-SELCALL------------å è-ID:1024 E e Push [EMG] for 2 sec. <Emergency Selcall menu> After selecting the channel at step w, push [OK ] to edit the Emergency selcall menu. -*2010:EMER1---------å --TX:20. 500. 0 --SelfID:1004 ç-EMER-SELCALL-------å è*ID:0000 e Push [ CLR] or [OK ] to select `EMER SELCALL. ' · `SELCALL, ' `GPS BCON, ' `GPS POSN, ' `EMER SELCALL, ' `PAGECALL, ' `STATUS CALL, ' `SEL BCON' are selectable. --2020:SELCALL --TX:-3. 200. 0 --SelfID:1004 ç-EMER-SELCALL-------å è-ID:1024 r Push [] to select `ID, ' then edit `0, ' `0, ' `0, ' `0' as no specified ID or select an intended ID. · Last selected ID is displayed. · Enter the 4-digits (or 6-digits depending on Initial set mode setting) number of the desired ID using 10-keypad directly. [. . . ] 43)) Outputs data terminal ready signal. Input terminal for data-set-ready signal. No connection. 4 9 6 DTR GND DSR RTS CTS NC 7 5 6 7 8 9 GPS q w Pin Pin name 1 2 NMEA + NMEA _ Description NMEA0183 ver 2. 0 or 3. 01 data input +. Ground for NMEA data. 62 8 D General SPECIFICATIONS D Transceiver · Output power : 1. 6­27. 9999 MHz 100/50/10 W p-p [AUS] 1. 6­3. 9999 MHz 125/50/10 W p-p [OTH] 4. 0­27. 9999 MHz 100/50/10 W p-p [OTH] · Spurious emission : Less than ­43 dB below peak output power (Less than ­40 dB for 3. 5­ 3. 9999 MHz range [OTH]) · Carrier suppression : More than 40 dB below peak output power · Unwanted sideband : More than 50 dB suppression below peak output power · Mic. [. . . ]