User manual ICOM IC-M710RT

[. . . ] INSTRUCTION MANUAL MF/HF MARINE TRANSCEIVER iM710RT IMPORTANT READ THIS INSTRUCTION MANUAL CAREFULLY before attempting to operate the transceiver. SAVE THIS INSTRUCTION MANUAL--This manual contains important safety and operating instructions for the IC-M710RT MF/HF MARINE TRANSCEIVER. EXPLICIT DEFINITIONS The explicit definitions described below apply to this instruction manual. DEFINITION Personal injury, fire hazard or electric RWARNING shock may occur. CAUTION NOTE Equipment damage may occur. No risk of personal injury, fire or electric shock. [. . . ] to program the user channel. Push and hold [RX] · Or rotate the [CHANNEL] selector to change the frequency. AGC F Use keypad or channel selector. ALM RX TX DSC DUP AGC F Programming is completed. D Transmit frequency (Not applicable for General versions) Select the desired user channel to be programmed. Push [TX]. Push [TX] ALM RX TX DSC DUP AGC F Push [CE] to select frequency selection mode. Enter the desired frequency via the keypad with 5 or 6 digits. · "s" and frequency appear on the display. · "$" flashes. "$" flashes. Push [CE] ALM RX TX DSC DUP AGC F Push and hold [TX] for 1 sec. Push [TX] to stop "$" from flashing. · The [CHANNEL] selector cannot be used. Push and hold [TX] after entering a frqeuency ALM RX TX DSC DUP AGC F D Channel names Select the desired user channel to be programmed. Push [CH/FREQ] to select channel indication. Rotate the [GROUP] selector for cursor position and the [CHANNEL] selector for name content. · The channel name (alphanumeric) readout flashes. Push [FUNC] then [CE] ALM RX TX DSC DUP AGC F "$" flashes. Rotate [GROUP] and [CHANNEL] to select cursor and character Push [RX] ALM RX TX DSC DUP Push and hold [RX] to program the name. · Flashing stops. · To return to the previous message, push [CE]. AGC F ALM RX TX DSC DUP AGC F 12 SET MODE I Set mode operation Set mode operation is used for programming infrequently changed values or conditions of functions. 6 NOTE: Some of the set mode items described in this section are not available on some transceiver versions. Push [POWER] to turn power off, if necessary. While pushing [FUNC] + [1], push [POWER] to turn Rotate the [GROUP] selector to select the desired item. Rotate the [CHANNEL] selector to set the values or conditions for the selected item. Turn power off and on again to exit set mode. power on and enter set mode. [POWER] [FUNC] [1] ALM RX AGC TX DSC F Condition Item I Set mode contents (1) FSK ITU channels FSK ITU channels appear as a group between the ITU 25 MHz band and user channels. This FSK channel group can be hidden for voice communication only. FSK channels don't appear (no SITOR operation). (default) FSK channels appear (for SITOR operation). (2) Connected antenna tuner The transceiver has several tuner control systems for use with an optional Icom antenna tuner. Select the condition depending on the connected antenna tuner. AT-130 (default) AT-120  NOTE: Internal switch selection may be required when using a non-Icom tuner (p. 23). AH-3 (3) Automatic tuning condition When the optional AT-130 or AT-130E automatic antenna tuner is connected, tuning can be started automatically without the [TUNE] switch, for instant operation. If manual tuning is required, this automatic operation can be deactivated. ALM RX AGC TX DSC F Tuning starts when pushing [PTT] on a new frqeuency. ALM RX AGC TX DSC F Tuning starts only when [TUNE] is pushed. (default) 13 6 SET MODE (4) Scan type selection (scan-type only) This item selects one of the following scan functions. Channel scan and channel resume scan search 5 channels around a user selected channel or search all ITU channels in the band when an ITU channel is selected. Programmed scan (optional) searches signals within the frequency range and activates slowly while squelch is open and fast while squelch is closed. ALM RX AGC TX DSC ALM RX AGC TX DSC ALM RX AGC TX DSC F F F Channel scan Scan is canceled when transmitting. (default) Channel resume scan Scan pauses when squelch opens, then resumes after 10 sec. Channel resume scan Scan operates over the frequency range. [. . . ] MN-100 ANTENNA MATCHER Matches the transceiver to a dipole antenna. 8 m × 2 antenna wires come attached. MN-100L ANTENNA MATCHER Matches the transceiver to a dipole antenna. 15 m × 1 antenna wire comes attached. [. . . ]