User manual ICOM IC-M80

[. . . ] No rsk of personal njury, fire or electrc shock. D FEATURES m Advanced receiver performance m Easy to hear speaker m Built-in DSC meets Class D requirement m Rugged waterproof construction m Favorite channel function m AquaQuake water draining function Icom, Icom Inc. and the logo are regstered trademarks of Icom Incorporated (Japan) n the Unted States, the Unted Kngdom, Germany, France, Span, Russa and/or other countres. CLEAN THE TRANSCEIVER AND MICROPHONE THOROUGHLY WITH FRESH WATER after exposure to water ncludng salt water, otherwse, the keys and swtches may become noperable due to salt crystallzaton. IN CASE OF EMERGENCY If your vessel requres assstance, contact other vessels and the Coast Guard by sendng a Dstress call on Channel 16. INSTALLATION NOTE The nstallaton of ths equpment should be made n such a manner as to respect the EC recommended electromagnetc field exposure lmts (1999/519/EC). The maxmum RF power avalable from ths devce s 25 watts. The antenna should be nstalled as hgh as possble for maxmum effcency and that ths nstallaton heght should be at least 5 meters above ground (or accessble) level. [. . . ] " dsappears. n Starting a scan Set scan type (Prorty or Normal scan) and scan resume tmer n advance, usng Set mode. 40) q Push both [Y] and [Z] to select the desred channel group, f desred. Set e Make sure the squelch s closed to start a scan. r Push [SCAN·TAG] to start Prorty or Normal scan. · "SCAN" blnks at the channel comment ndcator durng scannng. (Durng Prorty scan, "16" appears besde the blnkng "SCAN" ndcaton. ) · A beep tone sounds and "16" blnks at the channel comment ndcator when a sgnal s receved on Channel 16 durng Prorty scan. · When a sgnal s detected, scan pauses untl the sgnal dsappears or resumes after pausng 5 sec. (Channel 16 s stll montored durng Prorty scan. ) · Push [Y] or [Z] to check the scannng TAG channels, to change the scannng drecton or resume the scan manually. 4 r cancel the TAG channel settng, repeat step e. To Clearing (or setting) all tagged channels Whle pushng [HI/LO] on the mcrophone, push and hold [SCAN·TAG] for 3 sec. (untl a long beep changes to 2 short beeps) to clear all TAG channels n the channel group. · Repeat above procedure to set all TAG channels. t stop the scan, repeat step r. To Blinks Blinks [Example]: Starting a Normal scan. Push Scan starts. When a signal is Appears received. 11 5 DUALWATCH/TRI-WATCH n Operation q Select Dualwatch or Tr-watch n Set mode. 40) w Push [Y] or [Z] to select the desred channel. t Push [Y] or [Z] to set up to a 10-character ID name. · Push [CH·DUAL] or [16·C] to move the cursor forward or backward, respectvely. · Push [CLR] to cancel and ext the condton. D Programming Address ID q Push [MENU] to enter the DSC menu. w Push [Y] or [Z] to select "ADDRESS, " push [ENT]. y Push [ENT] to program and returns to the normal operaton. e Push [Y] or [Z] to select "ADD INDV ID, " push [ENT]. Scrolls r Push [Y] or [Z] to set the 9-dgt Indvdual ID, push [ENT]. · Push [CH·DUAL] or [16·C] to move the cursor forward or backward, respectvely. · Push [CLR] to cancel and ext the condton. 14 DSC OPERATION 6 D Deleting Address ID q Push [MENU] to enter the DSC menu. w Push [Y] or [Z] to select "ADDRESS, " and push [ENT]. D Programming Group ID q Push [MENU] to enter the DSC menu. w Push [Y] or [Z] to select "ADDRESS, " push [ENT]. 6 e Push [Y] or [Z] to select "DEL INDV ID, " push [ENT]. · When no address ID s programmed, "NO ID" s dsplayed. Scrolls Scrolls e Push [Y] or [Z] to select "ADD GROUP ID, " push [ENT]. r Push [Y] or [Z] to select the desred ID name for deletng and push [ENT]. · "READY" appears. r Push [Y] or [Z] to set the 9-dgt Group ID, push [ENT]. · Push [CH·DUAL] or [16·C] to move the cursor forward or backward, respectvely. · Push [CLR] to cancel and ext the condton. 1st dgt `0' s fixed for a Group ID. t Push [ENT] to delete the selected address ID and returns to the normal operaton. Contnue to the next page 15 6 DSC OPERATION D Deleting Group ID t Push [Y] or [Z] to set up to a 10-character ID name. · Push [CH·DUAL] or [16·C] to move the cursor forward or backward, respectvely. · Push [CLR] to cancel and ext the condton. q Push [MENU] to enter the DSC menu. w Push [Y] or [Z] to select "ADDRESS, " and push [ENT]. y Push [ENT] to program and returns to the normal operaton. e Push [Y] or [Z] to select "DEL GROUP ID, " push [ENT]. · When no group ID s programmed, "NO ID" s dsplayed. Scrolls r Push [Y] or [Z] to select the desred ID name for deletng and push [ENT]. · "READY" appears. t Push [ENT] to delete the selected group ID and returns to the normal operaton. 16 DSC OPERATION 6 n Position and time programming A dstress call should nclude the shp's poston and tme data. [. . . ] r Tghten the end bolts on the clamps (rotate clockwse) so that the clamps press frmly aganst the nsde of the nstrument control panel. t Tghten the lockng nuts (rotate counterclockwse) so that the transcever s securely mounted n poston as below. y Connect the antenna and power cable, then return the nstrument control panel to ts orgnal place. e Attach the clamps on ether sde of the transcever wth 2 suppled bolts (5 × 8 mm). · Make sure that the clamps algn parallel to the transcever body. t r 45 9 TROUBLESHOOTING POSSIBLE CAUSE SOLUTION · Check the connecton to the transcever. [. . . ]