User manual ICOM IC-P4CT

[. . . ] With proper care, this product should provide you with years of trouble-free operation. We want to take a couple of moments of your time to thank you for making your IC-P4CT your radio of choice, and hope you agree with Icom's philosophy of "technology first. " Many hours of research and development went into the design of your ICP7A. IMPORTANT READ ALL INSTRUCTIONS carefully and completely before using the transceiver. SAVE THIS INSTRUCTION MANUAL-- This instruction manual contains important operating instructions for the IC-P4CT. EXPLICIT DEFINITIONS DEFINITION Personal injury, fire hazard or electric shock R WARNING!CAUTION NOTE Equipment damage may occur. No risk of personal injury, fire or electric shock. [. . . ] · While pushing and holding [FUNC], rotate [DIAL] to select memory channel in 10 channel steps. t Push and hold [V/M] (SKIP·S. MW) for 1 sec. · 3 beeps sound · Memory channel number automatically increases when continuing to push [V/M] (SKIP·S. MW) after programming. [EXAMPLE]: Programming 145. 870 MHz into memory channel 20 (blank channel). Push WFMAM -DUP T SQL S. MW for 1 sec. WFMAM -DUP T SQL Rotate DTCS ATT WFMAM -DUP T SQL Push DTCS ATT S. MW for 1 sec. WFMAM -DUP T SQL DTCS ATT DTCS ATT WFMAM -DUP T SQL DTCS ATT VOL PRIO P SKIP MR 9 5 LOW 1 VOL PRIO P SKIP MR 9 5 LOW 1 VOL PRIO P SKIP MR 9 5 LOW 1 VOL PRIO P SKIP MR 9 5 LOW 1 VOL PRIO P SKIP MR 9 5 LOW 1 24 6 MEMORY/CALL CHANNELS Memory bank setting The IC-P4CT has a total of 18 banks (A to H, J, L, N, O to R, T, U and Y). Regular memory channels, 000 to 999, may assigned into a desired bank for easy memory management. qPush and hold [V/M] (SKIP·S. MW) for 1 sec. to enter select memory write mode. · 1 short and 1 long beep sound. ·" " indicator and memory channel number blink. rWhile pushing and holding [BAND] (TS·LOCK), rotate [DIAL] to select the desired bank. · Banks A to H, J, L, N, O to R, T, U and Y are available. · The bank can also be selected by pushing [BAND] (TS·LOCK) several times. Bank is selected with WFMAM -DUP T SQL + w Rotate [DIAL] to select the desired memory channel. eWhile pushing and holding [CALL] (MODE·SCAN), rotate [DIAL] to select "BANK. " · After releasing [CALL] (MODE·SCAN), "-- -- -- --" is displayed instead of the frequency indication, and only " " indicator blinks. · Bank group and channel number is displayed if the selected memory channel has already been assigned to a bank. · "BANK" can can also be selected by pushing [CALL] (MODE·SCAN) several times. [DIAL] WFMAM -DUP T SQL DTCS ATT VOL PRIO P SKIP MR 9 5 LOW 1 t Rotate [DIAL] to select the desired bank channel number. · Vacant bank channel numbers are only be displayed. Push [V/M] (SKIP·S. MW) to select memory mode, then rotate [DIAL] to select the desired memory channel. wPush and hold [V/M] (SKIP·S. MW) for 1 sec. to enter select memory write mode. · 1 short and 1 long beep sound. ·" " indicator and memory channel number blink. · Do not hold [V/M] (SKIP·S. MW) for more than 1 sec. otherwise the memory contents will be copied to VFO. wPush and hold [V/M] (SKIP·S. MW) for 1 sec. to enter select memory write mode. · 1 short and 1 long beep sound. ·" " indicator and memory channel number blink. e Rotate [DIAL] to select "VF. " r Push and hold [V/M] (SKIP·S. MW) for 1 sec. again. · VFO mode is selected automatically. e Rotate [DIAL] to select the target memory channel. rPush and hold [V/M] (SKIP·S. MW) for 1 sec. again to transfer. [EXAMPLE]: Copying channel 20 to 51. Select memory channel S. MW WFMAM -DUP T SQL Push DTCS ATT WFMAM -DUP T SQL S. MW for 1 sec. WFMAM -DUP T SQL Rotate DTCS ATT Push WFMAM -DUP T SQL S. MW for 1 sec. WFMAM -DUP T SQL DTCS ATT DTCS ATT DTCS ATT VOL PRIO P SKIP MR 9 5 LOW 1 VOL PRIO P SKIP MR 9 5 LOW 1 VOL PRIO P SKIP MR 9 5 LOW 1 VOL PRIO P SKIP MR 9 5 LOW 1 VOL PRIO P SKIP MR 9 5 LOW 1 29 MEMORY/CALL CHANNELS 6 Memory clearing Contents of programmed memories can be cleared (blanked), if desired. [. . . ] Keep the [MIC/SP] cap attached when jack are not in use to keep the contact clean. OPC-782 Microphone Microphone HM-153 Speaker/MIC connector HM-153P 15 SCAN SCAN S. MW S. MW SET SET 78 15 OPTIONS D LC-161 CARRYING CASE Helps protect the transceiver from scratches, etc. NOTE: When using as below illustration, tension release loop protects the [MIC/SP] connector from being damaged by cable stress or vibration OPC-782 HM-128 D HM-128 EARPHONE MICROPHONE An optional OPC-782 is required for connection. q w Transceiver D HM-131 SPEAKER MICROPHONE An optional OPC-782 is required for connection. HM-131 LC-161 Tension release loop e 79 POCKET GUIDE Important operating instructions are summed up in this and the following page for your simple reference. By cutting along the line and folding on the dotted line, it will become a card sized operating guide which can easily be carried in a card case or wallet, etc. <CUT HERE> 16 r Complete q Cut w Fold e Fold 80 <CUT HERE> POCKET GUIDE iP7A VFO and memory mode selection Push [V/M] to toggle between VFO and memory mode. [. . . ]