User manual ICOM IC-PW1EURO

[. . . ] INSTRUCTION MANUAL HF/50 MHz ALL BAND 1 kW LINEAR AMPLIFIER iPW1 iPW1EURO IMPORTANT READ THIS INSTRUCTION MANUAL CAREFULLY before attempting to operate the linear amplifier. SAVE THIS INSTRUCTION MANUAL. This instruction manual contains important safety and operating instructions for the IC-PW1/IC-PW1EURO. PRECAUTION RWARNING HIGH VOLTAGE!NEVER attach an antenna or internal antenna connector during transmission. This may result in an electrical shock or burn. [. . . ] Check that the applied voltage to pin 7 of [ACC-1]/[ACC-2] socket is 13. 8 V DC. 10 2 INSTALLATION AND CONNECTIONS I Separating the remote controller The control section of the linear amplifier can be separated from the main body, doubling as a remote controller. It can be placed on the exciter or in another convenient place. w Remove 8 screws from the sides of the linear amplifier, then lift up the top cover. y Replace the control cable with the supplied separation cable through the cable hole. Use the shorter end (from the bushing) to connect to the remote controller. Control cable JACK unit MAIN unit Separation cable (Fig. 1) u Remove 2 screws from the cable hole cover on the linear amplifier rear panel. Insert the separation cable into the cable hole. Keep the hole cover and screws for future use. Longer end (from the bushing) Control cable (step i) J3 CONTR OLLER Control cable (step e) (Fig. 2) e Unplug the control cable from J3 on the MAIN unit. r Remove 2 screws from the front panel of the linear amplifier, then detach the remote controller. 1) Attach the dummy panel onto the space left by the controller using the 2 screws. i Plug the other longer end (from the bushing) of the separation cable into J10 on the JACK unit through the cable hole. Connect the grounding wire as shown below. Connect the control cable to J11. Control cable J11 Separation cable To J3 (MAIN) J10 t Remove 5 screws from the rear panel of the remote controller, then remove the rear panel. JACK unit o Plug the other end of the control cable into J3 on the MAIN unit. 2) !0 Replace the top cover and 8 screws. 11 OPERATION I When first applying power (CPU resetting) Before first applying power, make sure all connections required for your system are complete by referring to chapter 2. Then, reset the linear amplifier using the following procedure. NOTE: Resetting CLEARS all programmed settings to default values. q Make sure the linear amplifier, exciter and auxiliary power supply (p. w While pushing [UP] and [DOWN], push [POWER] to turn power ON. - The internal CPU is reset. - The remote controller shows its initial condition when resetting is complete. 3 If the controller's power is supplied from non-Icom exciters or auxiliary power supply (p. 10), turn the exciter or auxiliary power supply ON while pushing [UP] and [DOWN] to reset the CPU. [POWER] e Reset the exciter's CI-V settings after resetting. 13, 14) [DOWN] [UP] I Setting the ALC levels R CAUTION: Final FETs may be damaged if the ALC level adjustment is set incorrectly. NOTE: Re-adjustment is necessary when replacing the exciter. [. . . ] remote controller) : 2-conductor 3. 5(d) mm (1/8") DECLARATION OF CONFORMITY We Icom Inc. Japan 1-1-32, Kamiminami, Hirano-ku Osaka 547-0003, Japan Declare on our sole responsibility that this equipment complies with the essential requirements of the Radio and Telecommunications Terminal Equipment Directive, 1999/5/EC, and that any applicable Essential Test Suite measurements have been performed. Kind of equipment: Type-designation: HF+50 MHz 1 kW LINEAR AMPLIFIER Düsseldorf 1st Dec. 2006 Place and date of issue Icom (Europe) GmbH Himmelgeister straße 100 D-40225 Düsseldorf Authorized representative name iPW1EURO+ OPC-853 Version (where applicable): This compliance is based on conformity according to Annex III of the directive 1999/5/EC using the following harmonised standards: i) Article 3. 1a EN 60950-1 (2001) H. Ikegami General Manager EN60065:2002 +A1:2006 (Power supply) EN60065:1998 (Power supply) ii) Article 3. 1b iii) Article 3. 2 EN 301489-1 and EN 301489-15 EN 301 783-2 Signature 19 SPECIFICATIONS 5 INSTALLATION NOTES For amateur base station installations it is recommended that the forwards clearance in front of the antenna array is calculated relative to the EIRP (Effective Isotropic Radiated Power). [. . . ]