User manual ICOM IC-R10

[. . . ] INSTRUCTION MANUAL COMMUNICATIONS RECEIVER iR10 This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. IMPORTANT READ ALL INSTRUCTIONS CAREFULLY before attempting to operate the receiver. CAUTIONS RWARNING!NEVER connect the receiver to an AC outlet. This may pose a fire hazard or result in an electric shock. SAVE THIS INSTRUCTION MANUAL -- This instruction manual contains important safety and operating instructions for the IC-R10. RWARNING! [. . . ] Programming details -- cont. e Push [EDIT], then rotate [DIAL] to select receive mode. r Push [EDIT], then rotate [DIAL] to select the skip scan condition. t Push [EDIT], then rotate [DIAL] to select the attenuator condition. y Push [EDIT], then rotate [DIAL] or enter alphanumeric characters to program a BANK name. · When you enter channel names with [DIAL] or a character assigned to the same key, push [ENT] before you enter the next character to change the digit (see page 72 for alphanumeric key assignments). Programming details -- cont. u Push [EDIT], to display your programmed frequency for confirmation. When the correct frequency is displayed, push [EDIT] for 2 sec. to return to VFO mode. When you want to return to VFO mode immediately, push [EDIT] for 2 sec. at any time. 28 4 MEMORY MODE I Programming example 1 -- (118. 0250 MHz; AM to channel B07) 1. BANK and memory channel setting q Push [V/M] to select MEMORY mode. w While pushing [FUNC], rotate [DIAL] to select BANK "B". FUNC 2. Data setting q Push [V/M] to select VFO mode. w Push [MODE] one or more times to select AM mode. MODE VFO AM 3. Programming the data While pushing [FUNC], push [(V/M)MW] for 2 sec. + [DIAL] B: MEMO FM 144. 0000 e Push numeral keys or rotate [DIAL] to set the frequency 118. 0250 MHz. 1 1 8 VFO AM e Push [0] and [7] to enter the memory channel number. 0 7 118. B07 MEMO FM . BLANK . 0 2 VFO AM "BLANK" appears when the memory channel is not programmed. 118. 0250 5 ENT 29 MEMORY MODE 4 I Programming example 2 -- (59. 75 MHz; WFM to channel A45) 1. Setting the frequency q Push [V/M] to select VFO mode. w Push [MODE] one or more times to select WFM mode. MODE WFM VFO 2. Set the BANK and memory channel q While pushing [FUNC], push [(V/M)MW] to enter memory write mode. w While pushing [FUNC], rotate [DIAL] to select BANK "A". FUNC 3. Programming the data While pushing [FUNC], [(V/M)MW] for 2 sec. push 144. 0000 VFO e Push numeral keys or rotate [DIAL] to set the frequency to 59. 75 MHz. 5 WFM VFO + [DIAL] SET BANK A: WFM 9 59. 7500 . 7 e Rotate [DIAL] select channel "45" or push [4] and [5] to enter the memory channel number. VFO 5 ENT [DIAL] or 4 5 SET CH NO. A45 BLANK "BLANK" appears when the memory channel is not programmed. WFM 30 4 MEMORY MODE I Programming example 3 -- (121. 5 MHz, EMER. , AM, SKIP: OFF, ATT: OFF, Aviation to channel F01) 1. Setting the frequency q Push [V/M] to select VFO mode. [. . . ] · 2 or more memory channels have not been programmed. · No channels have been programmed with the selected receive mode (when using mode select scan). SOLUTION · Rotate [SQL] counterclockwise. · Set receive mode to one of FM, WFM or AM. · Set scan edges to different frequencies. [. . . ]