User manual ICOM IC-R20

[. . . ] INSTRUCTION MANUAL COMMUNICATIONS RECEIVER iR20 This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. WARNING: MODIFICATION OF THIS DEVICE TO RECEIVE CELLULAR RADIO TELEPHONE SERVICE SIGNALS IS PROHIBITED UNDER FCC RULES AND FEDERAL LAW. FOREWORD Thank you for purchasing this Icom product. The IC-R20 COMMUNICATIONS RECEIVER is designed and built with Icom's superior technology and craftsmanship. [. . . ] eWhile pushing [8 SET], rotate [R-DIAL] to select "BANK. " · "BANK" item can also be selected by pushing [8 SET] several times. · Bank group and channel number is displayed if the selected memory channel has already been previously assigned into a bank. FM µ . >BANK-:A-00 -BNAME: 146. 010 012 Bank group is selected with BAND tAfter releasing [BAND], rotate [R-DIAL] to select the bank channel number from "00" to "99. " · Vacant bank channel numbers will only be displayed. FM [R-DIAL] µ . -BANK-:----BNAME: -MNAME: -SKIP-:OFF >CLEAR SET 146. 010 012 µ . >BANK-:A-00 -BNAME: 146. 010 012 Bank channel is selected with [R-DIAL] BAND After MR S. MW 8 is pushed yPush [MR S. MW] for 1 sec. to set the channel into the bank. · Return to the previous indication. FM SET 8 µ . >BANK-:---- 146. 010 012 27 MEMORY CHANNELS 6 Memory bank selection q Push [MR S. MW] to select memory mode. wWhile pushing [BAND], rotate [R-DIAL] to select the desired bank (A to Z). · The bank can also be selected by pushing [BAND] several times. · Only programmed banks are displayed. -DUP TSQL MODE FM ANL eRotate [R-DIAL] to select the bank channel. · Only programmed channels are displayed. -DUP TSQL MODE FM ANL AFC 145 870 µ A99 Bank initial Bank chanel number PSKIP AFC ATT 6 [R-DIAL] 145 870 µ 001 PSKIP ATT BAND Rotate [R-DIAL] while pushing [BAND] -DUP TSQL MODE AM ANL rTo return to regular memory condition, rotate [R-DIAL] while pushing [BAND], or push [BAND] several times. MR S. MW AFC 118 000 µ A12 PSKIP Only the programmed banks appear. -DUP TSQL MODE FM ANL AFC 438 720 µ Y01 PSKIP 28 6 MEMORY CHANNELS Programming memory/bank name Each memory channel can be programmed with an alphanumeric channel name for easy recognition and can be indicated independently by channel. w Rotate [R-DIAL] to select the desired memory channel. to select the select memory write condition. · 1 short and 1 long beep sound. µ · "µ " indicator blinks. FM tRotate [R-DIAL] to select the desired character. · The selected character blinks. · While pushing [6 M. N], rotate [R-DIAL] to select the character group. yWhile pushing [BAND], rotate [R-DIAL] to move the cursor to left or right. · Push [BAND] to move the cursor to right. Bank name FM Memory name FM µ . >BANK-:C-11 145. 700 -BANK-:C-11 >BNAME:GRO -MNAME: 012 145. 700 µ . 012 µ . -BANK-:C-11 >BNAME: >MNAME:Ric 145. 700 012 rWhile pushing [8 SET], rotate [R-DIAL] to select "BNAME" or "MNAME" when programming the memory name or the bank name, respectively. · The item can also be selected by pushing [8 SET] several times. · After selecting the memory or bank name programming condition, a cursor blinks for the first digit. Bank name selection FM uRepeat steps t and y until the desired 8-character channel names are displayed. to program the name and exit the channel name programming condition. · 3 beeps sound. Memory name selection FM -BANK-:C-11 >BNAME: -MNAME: 145. 700 µ . 012 µ . -BANK-:C-11 >BNAME: >MNAME: 145. 700 012 NOTE: Only one bank name can be programmed into each bank. Therefore, the previously programmed bank name will be displayed when bank name indication is selected. Also, the programmed bank name is assigned for the other bank channels automatically. 29 MEMORY CHANNELS D Available characters 6 ABCDEFGHIJKLMNOP QRSTUVWXYZ abcdefghijklmnop qrstuvwxyz 0123456789 Ò¨Î!"#$%&'()*+, -. /:;<=>?@[\]^_{ |}~ 01243 (space) Selecting memory/bank name indication During memory mode operation, one of the programmed memory name or bank name can be displayed below the frequency indication. -DUP TSQL MODE FM ANL AFC [R-DIAL] B:GROUP1 145 700 µ 012 PSKIP 6 ATT -DUP TSQL MODE FM ANL AFC M. N 6 M:Ricky 145 700 µ 012 PSKIP When no memory or bank name is programmed with the selected memory channel, no indication is displayed. -DUP TSQL MODE FM ANL AFC B:GROUP1 145 700 µ 012 PSKIP q Push [MR S. MW] to select memory mode. · Push [BAND] several times to select the desired bank group. wWhile pushing [6 M. N], rotate [R-DIAL] to select display indication type from bank name or memory name. [. . . ] Audio level setting Rotate [L-DIAL] (or push [Y]/ [Z]) to set the audio level. Squelch level setting While pushing [SQL], rotate [RDIAL] to set the squelch level. 92 <CUT HERE> POCKET GUIDE Frequency setting q Push [VFO MHz] to select VFO mode. w Rotate [R-DIAL] to set the desired operating frequency. · Entering keypad directly can be selected the desired frequency. · Push [9 TS] again to return to the previous condition. Frequency band selection Push [BAND] several times, or while pushing [BAND], rotate [RDIAL] to select the desired frequency band. [. . . ]