User manual ICOM IC-R72

[. . . ] CAUTION NOTE Equipment damage may occur. No risk of personal injury, fire or electric shock. WORD D FEATURES Wide frequency coverage with all mode receive Both Remote controller operation and PC control application are available ANF and NR functions are available (Only when the optional DSP unit is installed. ) IF shift function i Icom, Icom Inc. and the logo are registered trademarks of Icom Incorporated (Japan) in the United States, the United Kingdom, Germany, France, Spain, Russia and/or other countries. PRECAUTIONS RWARNING! [. . . ] subaudible tone frequency, scan skip information, etc. ) if required. ePush [S. MW·MW] to enter select memory write mode. · "!" indicator and the memory channel number blink. rRotate [DIAL] to select the desired memory channel to be programmed. · Memory channels not yet programmed are blank. t Push and hold [S. MW·MW] for 1 sec. to program. · 3 beeps sound · Memory channel number automatically increases when continuing to push [S. MW·MW] after programming. CONVENIENT Memory programming can be performed in versatile ways e. g. memory channel to the same (or different) memory channel, etc. [EXAMPLE]: Programming 145. 800 MHz into memory channel 20 (blank channel). Push Rotate for setting frequency, etc. Push . "Beep Rotate Push for 1 sec. and continue to push " "Beep " Beep " Beep " 17 "Beep MEMORY OPERATION 5 Programming channel names Each memory channel can be programmed with an alphanumeric channel name for easy recognition and can be indicated independently by channel. Names can be a maximum of 6 characters-- see the table below for available characters. (space) (I) (R) (0) (9) (A) (J) (S) (1) (+) (B) (K) (T) (2) (­) (C) (L) (U) (3) (/) (D) (M) (V) (4) (=) (E) (N) (W) (5) (F) (O) (X) (6) (G) (P) (Y) (7) (H) (Q) (Z) (8) q Select the desired memory channel to be programmed. Push [MR·SKIP] to select memory mode, then rotate [DIAL] to select the desired memory channel. wPush [S. MW·MW] to enter select memory write mode. · "!" indicator and the memory channel number blink. e Push [TS·MODE] twice to select the memory name programming condition, "m nAmE. " · Frequency readouts disappear and a cursor blinks. 5 r Rotate [DIAL] to select the desired character. · The selected character blinks. t Push [SET·LOCK] to move the cursor to the right. · Repeat pushing [SET·LOCK] to return to the first digit. y Repeat steps r and t until the desired channel names are displayed. u Push and hold [S. MW·MW] for 1 sec. to program the name and exit select memory write mode. [EXAMPLE]: Programming "CLUB" into memory channel 12. Select memory channel. to program the bank and exit select memory write mode. [TS·MODE] After [TS·MODE] released 22 5 MEMORY OPERATION Memory bank selection qPush [MR·SKIP] to select memory mode. wPush [MR·SKIP] again to enter memory type selection mode. Transferring bank contents [ The bank contents of programmed memory channels can be cleared or transferred to another bank. INFORMATION: Even if the memory bank contents are cleared, the memory channel contents still remain programmed. [DIAL] [MR·SKIP] eRotate [DIAL] to select the desired bank (A to H, J to R, T, U, W or Y). · Only programmed banks are displayed. r Push any switch to set the bank indication. · Bank's indicator appears at top of the memory channel. qSelect the desired bank contents to be transferred or erased from the bank. Push [MR·SKIP] to select memory mode. Push [MR·SKIP] again then rotate [DIAL] to select the desired memory bank. t Rotate [DIAL] to select the contents in the bank. yTo return to regular memory mode, repeat steps w­r and select "bAnk --" at step e. · Memory bank indication [DIAL] [MR·SKIP] Bank's indicator appears Push any switch to select the bank then rotate [DIAL] to select the desired contents. wPush [S. MW·MW] to enter select memory write mode. · "!" indicator and the memory channel number blink. Bank indicator appears 23 MEMORY OPERATION 5 ePush [TS·MODE] once to select "bAnk. " · The bank's indicator and bank channel are displayed. tPush and hold [S. MW·MW] for 1 sec. to program the bank and exit select memory write mode. 5 [S. MW·MW] [TS·MODE] After [TS·MODE] released yRepeat steps q to t for transferring or erasing an another banks contents. rRotate [DIAL] to select the desired bank indicator to transfer or erase. · Push [SET·LOCK] to toggle the bank or bank channel selection. · Select "-- --" indication when erasing the contents from the bank. [. . . ] to reset the CPU. [SET·LOCK] [PWR] [S. MW·MW] 45 OTHER FUNCTIONS 10 Internal audio switch The internal switch must be toggled when using an external speaker, headphones or earphone. Before removing the top cover, turn the receiver power OFF, then disconnect the DC power cable. q Turn the power OFF, then disconnect the DC power cable. wUnscrew the 8 screws and disconnect the connected cables, then remove the top cover. · Be careful not to lost the screws. [. . . ]