User manual ICOM IC-RP1510

[. . . ] NEVER EXPLICIT DEFINITIONS The following explicit definitions apply to this manual. DEFINITION Personal injury, fire hazard or electric shock RWARNING may occur. CAUTION NOTE Equipment damage may occur. No risk of personal injury, fire or electric shock. [. . . ] Setting receive conditions q Select VFO mode (p. w Set the frequency and receive mode (p. BANK and memory channel setting While pushing [FUNC], push [(V/M)MW]. 1 12 26 4 MEMORY MODE I Programming a memory channel -- 3 This is the easiest way to memorize the received frequency, mode and other information along with memory, BANK names, scanning condition, etc. Programming details q Push [EDIT] to enter memory programming mode. w Rotate [DIAL] or enter the alphanumeric characters via the keypad to program a memory name. · When you enter channel names with [DIAL] or a character assigned to the same key, push [ENT] before you enter the next character to change the digit (see page 72 for alphanumeric key assignments). 1. Set up q Set the frequency you want to program in VFO mode. w While pushing [FUNC], push [(V/M)MW] to enter memory write mode. 2 2. BANK and memory channel setting q While pushing [FUNC], rotate [DIAL] to select the BANK you want to program (p. w Rotate [DIAL] or push 2 digit keys to select the memory channel you want to program (p. 24). 2 1 27 MEMORY MODE 4 3. Programming details -- cont. 3 Push [EDIT], then rotate [DIAL] to select receive mode. BANK and memory channel setting q While pushing [FUNC], push [(V/M)MW]. w While pushing [FUNC], rotate [DIAL] to select BANK "F". FUNC 3. Programming details q Push [EDIT] to enter memory setting mode. EDIT FM VFO VFO + [DIAL] SET BANK F: FM SET CH NAME F01 w Rotate [DIAL] until the character "E" appears then push [ENT] or push [3] twice to enter the "E. " VFO 1 FM VFO 2 1 121. 5000 e Rotate [DIAL] or push [0] then [1] to select channel "01". VFO . 5 ENT FM [DIAL] ENT SET CH NAME F01 E FM [DIAL] SET CH NO. F01 BLANK or 3 52 e Rotate the [DIAL] then push [ENT] to enter the characters "M", "E", "R" and ". " for memory names or push numeral keys (see page 72 for alphanumeric key assignments). Programming details -- cont. t Push [EDIT] to change the receive mode item. y Rotate [DIAL] to select AM mode, then push [EDIT] to change the item. VFO 3. Programming details -- cont. i Rotate [DIAL] to select the OFF position for attenuator setting, then push [EDIT]. VFO FM 3. Programming details -- cont. !1 The display shows the programmed frequency for confirmation; push and hold [EDIT] for 2 sec. if the frequency is correct. · After pushing and holding [EDIT], VFO mode is automatically selected. [DIAL] [DIAL] SET MODE MODE:AM FM SET ATT ATT: OFF EDIT u Rotate [DIAL] to select the OFF position for SKIP setting, then push [EDIT]. VFO o Rotate [DIAL] until the character "A" appears, then push [ENT] or push [2] once to enter "A". VFO Push for 2 sec. VFO AM 121. 5000 [DIAL] ENT SET B-NAME F:A FM [DIAL] SET SKIP SKIP: OFF FM or 2 !0 Rotate [DIAL ]then push [ENT] to enter the characters for BANK names or push numeral keys (see page 72 for alphanumeric key assignments). 32 4 MEMORY MODE I Memory copy What is the memory copy function?The memory copy function copies the contents (minus BANK names) of the selected memory channel to VFO or to another memory channel. [. . . ] · Set [CHARGE] to the ON position. 8 75 TROUBLESHOOTING 13 PROBLEM Cannot start scanning. POSSIBLE CAUSE · [SQL] is rotated too far clockwise. · Incorrect receive mode (LSB, USB or CW) is selected. · Scan edges are set to the same frequencies. [. . . ]