User manual ICOM IC-RX7

[. . . ] INSTRUCTION MANUAL WIDEBAND RECEIVER iRX7 This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. WARNING: MODIFICATION OF THIS DEVICE TO RECEIVE CELLULAR RADIOTELEPHONE SERVICE SIGNALS IS PROHIBITED UNDER FCC RULES AND FEDERAL LAW. FOREWORD Thank you for purchasing this Icom product. The IC-RX7 wideband receiver is designed and built with Icom's superior technology and craftsmanship. [. . . ] several times to select the desired category; or push [v] or [w] several times to select the desired group. · Push [HOLD V] again to restart the scan. w Push [r]/[s] (or rotate [DIAL]) to select the desired category, then push [ENT MW]. · Scan pauses when a signal is received. · Rotate [DIAL] to change the scanning direction. MENU DIAL NO. MENU CLR SQL MW ENT HOLD 1 4 2 5 8 0 3 6 9 SKIP MW ENT ENT Push MW HOLD V SCAN SEARCH . 7 ATT e Push [HOLD V] to stop the scan temporarily, if desired. · Push and hold [v] or [w] for 1 sec. several times to select the desired memory category; or push [v] or [w] several times to select the desired group. · Push [HOLD V] again to restart the scan. 42 SEARCH AND SCAN OPERATIONS 6 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 43 Group scan Group scan repeatedly scans all memory channels in the same group as the selected memory channel has been programmed. q Select the category that includes the desired group to be scanned. Push [SCAN] to start a scan, then push [HOLD V] to hold the scan. w Enter "GROUP SCAN" in SCAN menu. MENU SCAN GROUP SCAN (Push [MENU ]), (Push [r]/[s], then push [ENT MW]. ) HOLD V MENU DIAL NO. MENU ENT Push MW CLR SQL MW ENT HOLD SCAN SEARCH 1 4 2 5 8 0 3 6 9 SKIP MW ENT · SCAN menu can also be entered by pushing and holding [SCAN] for 1 sec. . 7 ATT e Push [r]/[s] (or rotate [DIAL]) to select the desired group, then push [ENT MW]. · Scan pauses when a signal is received. · Rotate [DIAL] to change the scanning direction. ENT Push MW r Push [HOLD V] to stop the scan temporarily, if desired. · Push and hold [v] or [w] for 1 sec. several times to select the desired memory category; or push [v] or [w] several times to select the desired group. · Push [HOLD V] again to restart the scan. 6 SEARCH AND SCAN OPERATIONS Weather channel operation There are 10 weather channels for monitoring weather channels from the NOAA (National Oceanic and Atmospheric Administration) broadcasts. U. S. A. and CANADA versions only D Weather alert function NOAA broadcast stations transmit weather alert tones before important weather announcements. When the weather alert function is turned ON, the selected weather channel is monitored every 5 sec. When the alert signal is detected, the "ALT" and the WX channel are displayed alternately and sounds a beep tone until the receiver is operated. The previously selected (used) weather channel is checked periodically during standby or while scanning. w Enter "WEATHER ALERT" in SCAN menu. MENU SCAN WEATHER ALERT (Push [MENU ]), (Push [r]/[s], then push [ENT MW]. ) · SCAN menu can also be entered by pushing and holding [SCAN] for 1 sec. D Weather channel selection q Enter "WEATHER SCAN" in SCAN menu. MENU SCAN WEATHER SCAN (Push [MENU ]), (Push [r]/[s], then push [ENT MW]. ) · SCAN menu can also be entered by pushing and holding [SCAN] for 1 sec. · "WX" and the weather channel number appear. w Push [HOLD V] to stop scanning. e Rotate [DIAL] to select the desired weather channel. to return to VFO mode. [DIAL] e Push [r]/[s] (or rotate [DIAL]) to select "ON" or "OFF. " MENU DIAL NO. MENU CLR SQL MW ENT HOLD V 1 4 2 5 8 0 3 6 9 SKIP MW ENT ENT Push MW HOLD V SCAN SEARCH . 7 ATT r Push [ENT MW] (or [v]) to return to SCAN menu, and push [CLR SQL] to return to the weather channel indication. 44 SEARCH AND SCAN OPERATIONS 6 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 45 Skip setting for scanning t Set the desired stand-by condition. · Select VFO or memory channel. [. . . ] · Set the receiving mode correctly in MODE/TS/ TONE. . . · The battery pack or batteries is/are almost · Charge the battery pack or replace the batteries. · The lock function is activated. Key operation cannot work · The monitor function is activated. [. . . ]