User manual ICOM IC-T41E

[. . . ] This radio has been tested and complies with the FCC RF exposure limits for "Occupational Use Only". In addition, your Icom radio complies with the following Standards and Guidelines with regard to RF energy and electromagnetic energy levels and evaluation of such levels for exposure to humans: · FCC OET Bulletin 65 Edition 97-01 Supplement C, Evaluating Compliance with FCC Guidelines for Human Exposure to Radio Frequency Electromagnetic Fields. · American National Standards Institute (C95. 1-1992), IEEE Standard for Safety Levels with Respect to Human Exposure to Radio Frequency Electromagnetic Fields, 3 kHz to 300 GHz. · American National Standards Institute (C95. 3-1992), IEEE Recommended Practice for the Measurement of Potentially Hazardous Electromagnetic Fields­ RF and Microwave. [. . . ] w Slide the belt clip in the direction of the arrow until the belt clip is locked and makes a `click' sound. q w w q w q To detach the belt clip: q Release the battery pack if it is attached. w Pinch the clip (q), and slide the belt clip in the direction of the arrow (w). w q 4 5 2 PANEL DESCRIPTION q IC-F14S/F24S PANEL DESCRIPTION 2 2 I Front, top and side panels IC-F14/F24 e LED INDICATOR (p. Lights green while receiving a signal, or when the squelch is open. Lights/blinks orange when the matched 2/5-tone code is received, according to the pre-programming. r SPEAKER-MICROPHONE CONNECTOR [SP MIC] Connects the optional speaker-microphone. 31) i u w e Speaker y t r Microphone [SP MIC] jack cover NOTE: Attach the [SP MIC] jack cover when the optional speaker-microphone is not used. 4) t DEALER-PROGRAMMABLE KEY [Lower] The desired function can be assigned by your dealer. 9) y PTT SWITCH [PTT] Push and hold to transmit; release to receive. u DEALER-PROGRAMMABLE KEY [Upper] The desired function can be assigned by your dealer. 9) i ANTENNA CONNECTOR Connects the supplied antenna. q CHANNEL SW/SELECTOR · IC-F14S/F24S: Toggle the channel switch to select the pre-programmed channel 1 or 2. (PMR operation only) Ask your dealer for details. Push and hold to select the IF bandwidth to narrow. 10 11 3 CONVENTIONAL OPERATION I Call procedure [VOL] CONVENTIONAL OPERATION 3 I Turning power ON Rotate [VOL] to turn power ON. When your system employs tone signalling (excluding CTCSS and DTCS), the call procedure may be necessary prior to voice transmission. The tone signalling employed may be a selective calling system which allows you to call specific station(s) only and prevent unwanted stations from contacting you. q Select the desired TX code channel or 2/5-tone code according to your System Operator's instructions. · This may not be necessary depending on programming. 3 I Channel selection IC-F14S/F24S: Toggle [CHANNEL SWITCH] to select the channel 1 or 2, or, push one of [MRCH 1] to [MR-CH 4] key to select a channel directly. · The memory channels 3 and 4 are available when [MR-CH 3] and [MR-CH 4] keys are assigned. [CHANNEL SWITCH] w Push the call key (assigned to one of the dealer programmable keys. ) (p. 11) e After transmitting a 2/5-tone code, the remainder of your communication can be carried out in the normal fashion. Selective calling Non-selective calling IC-F14/F24: Rotate [CHANNEL SELECTOR] to select the desired operating channel, in sequence; or, push one of [MR-CH 1] to [MR-CH 4] key to select a channel directly. [CHANNEL SELECTOR] AUTOMATIC SCAN TYPE: Channel setting is not necessary for this type. When turning the power ON, the transceiver automatically starts scanning. Scanning stops when receiving a call. 12 13 3 CONVENTIONAL OPERATION CONVENTIONAL OPERATION 3 I Receiving and transmitting NOTE: Transmitting without an antenna may damage the transceiver. 2 for antenna attachment. D Transmitting notes · Transmit inhibit function The transceiver has several inhibit functions which restrict transmission under the following conditions: - The channel is in mute condition. - Un-matched (or matched) CTCSS is received. - The selected channel is a `receive only' channel. · Time-out timer After continuous transmission for the pre-programmed time period, the time-out timer activates, and causes the transceiver to stop transmitting. [. . . ] 1 q w e Clip the belt clip to a part of your belt. And insert the transceiver into the belt clip until the base clip inserted fully into the groove. 6 I To attach q Release the battery pack if it is attached. 3) w Slide the base clip in the direction of the arrow until the base clip is locked and makes a `click' sound. r Once the transceiver is locked in place, it swivels as illustrated below. 26 27 6 SWIVEL BELT CLIP SWIVEL BELT CLIP 6 I To detach q Turn the transceiver upside down in the direction of the arrow and pull out from the belt clip. [. . . ]