User manual ICOM IC-T42A

[. . . ] NEVER short the terminals of the battery pack. EXPLICIT DEFINITIONS DEFINITION Personal injury, fire hazard or electric shock RWARNING may occur. CAUTION NOTE Equipment damage may occur. No risk of personal injury, fire or electric shock. WORD DO NOT push [PTT] when not actually desiring to transmit. AVOID using or placing the transceiver in direct sunlight or in areas with temperatures below ­25°C or above +55°C. The basic operations, transmission and reception of the transceiver are guaranteed within the specified operating temperature range. [. . . ] to enter the ID code edit mode for 5-tone code. Then set the desired digit using [CH Up]/[CH Down] or 10-keypad*. 13) *10-key versions only TX CODE CHANNEL UP/DOWN KEYS Push to select a TX code channel directly. ID-MR SELECT KEYS Recalls detected ID codes. 2 · Push this key, then select the ID code using [CH Up]/[CH Down]. · Up to 5 ID's are memorized. 2 Push and hold for 1 sec. SCRAMBLER FUNCTION Push to toggle the voice scrambler function ON and OFF. USER SET MODE KEY Push and hold for 1 sec. to enter user set mode. · During user set mode, push this key to select an item, and change the value or condition using [CH Up]/[CH Down]. Push and hold this key for 1 sec. User set mode is also available via the `Power ON function. ' Refer to (p. OPT OUT KEYS Push to control the output signal level of the optional ports in the optional unit connector. When turning power ON, the transceiver automatically starts scanning. e Push [TX Code CH Select] several times to select the desired digit to be edited. · The digit to be edited blinks. r Push [CH Up], [CH Down] or 10-keypad* to set the desired digit. t Push [TX Code CH Select] to set the digit. The digit to the right will blink automatically. · When the 10-keypad* is used for setting, the digit to be edited moves to the right automatically without pushing [TX Code CH Select]. y Repeat r and t to input all allowable digits. u After setting the last digit, push [TX Code CH Select] to set the code and return to the stand-by mode. *10-key versions only 13 3 BASIC OPERATION USING [TX CODE ENTER] KEY: q Select the desired TX code channel via [TX Code CH Select]+[CH Up] or [CH Down], [TX Code CH Up] or [TX Code CH Down]. 13) w Push [TX Code Enter] to enter the TX code edit mode. e Push [TX Code Enter] several times to select the desired digit to be edited. · The digit to be edited blinks. I User set mode User set mode is accessed at power ON and allows you to set seldom-changed settings. In this case you can "customize" the transceiver operation to suit your preferences and operating style. Entering the user set mode: q While pushing and holding [Side2] and [Side3], rotate [VOL] to turn the power ON. w Push [P0] several times to select the appropriate item. Then push [CH Up] or [CH Down] to set the desired level/condition. · Available set mode functions are Backlight, Beep, Beep Level, SQL Level, Mic Gain, Battery Voltage and Signal Moni. r Push [CH Up], [CH Down] or 10-keypad* to set the desired digit. t Push [TX Code Enter] to set the digit. [. . . ] Otherwise the transceiver may not be attached to the holder or swivel properly if the transceiver is accidentally dropped and the base clip is scratched or damaged. 23 7 BP-231 BP-232 BP-240 OPTIONS D BELT CLIPS Capacity 1150 mAh 2000 mAh Battery life* 9 hrs. 15. 5 hrs. 1 D BATTERY PACK Battery pack Voltage 7. 4 V 7. 4 V · MB-93 SWIVEL BELT CLIP · MB-94 BELT CLIP Exclusive alligator-type belt clip. The same as supplied with the transceiver. · MB-96N/96F LEATHER BELT HANGER Battery case for AAA (LR03) × 6 alkaline D OPTIONAL UNITS · UT-108R DTMF DECODER UNIT Provides pager and code squelch capabilities. [. . . ]