User manual ICOM IC-U82

Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets... DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!

Sponsored Links

If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Lastmanuals provides you a fast and easy access to the user manual ICOM IC-U82. We hope that this ICOM IC-U82 user guide will be useful to you.

Lastmanuals help download the user guide ICOM IC-U82.


ICOM IC-U82 : Download the complete user guide (4260 Ko)

You may also download the following manuals related to this product:

   ICOM IC-U82 BROCHURE (798 ko)
   ICOM IC-U82 AUTRE NOTICE (4282 ko)
   ICOM IC-U82 INSTRUCTION MANUAL (4254 ko)
   ICOM IC-U82 SUPPLEMENTARY GUIDE (22 ko)

Manual abstract: user guide ICOM IC-U82

Detailed instructions for use are in the User's Guide.

[. . . ] INSTRUCTION MANUAL VHF TRANSCEIVER iV82 iV82-T UHF TRANSCEIVER iU82 This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. IC-V82 IC-U82 FOREWORD Thank you for purchasing this Icom product. The IC-V82/U82 VHF/UHF TRANSCEIVERS are designed and built with Icom's superior technology and craftsmanship. With proper care, this product should provide you with years of trouble-free operation. [. . . ] intervals) is the slowest. PWR PRIO 7 SET 8 H/M/L 9 ENT ENT rPush [·ENT ] to exit INITIAL SET MODE. 29 8 Band edge SCAN OPERATION Programmed scan End 1b 2b 3b Scan types PROGRAMMED SCAN Start 1A 2A 3A Scan edges Scan Jump Programmed scan P1 scans between 1A and 1b, P2 scans between 2A and 2b, and P3 scans between 3A and 3b frequencies. Band edge Programmed scan repeatedly scans between two user programmed frequencies (memory channels "1A­3A" and "1b­3b") or scans between upper and lower band edges. This scan is useful for checking for signals within a specific frequency range such as repeater output frequencies, etc. wPush [A·FUNC] and [5·SCAN] to start the scan, then a selected scan edge appears as "P1, " "P2, " "P3" or "AL. " · To change the scan edge, push [A·FUNC] and [8·SET] several times until the desired scan edge appears. · "AL" for full scan, "P1", "P2" and "P3" for programmed scan between the programmed scan edge channels as "1A"­"1b, " "2A"­"2b" and "3A"­"3b. " Y Z · To change the scan direction, push [Y] or [Z]. · When [VOL] is assigned as tuning dial, rotate [VOL] to change the scan direction. 14, 65) Push A FUNC MEMORY (SKIP) SCAN Mch 1 Mch 0 Mch 199 Mch 10 Mch 2 Mch 3 Mch 4 Mch 5 SKIP Mch 9 Mch 8 SKIP Mch 7 Mch 6 PRIORITY WATCH Priority memory channel watch VFO frequency 145. 20 MHz 5 sec. Mch 3 Priority channel SCAN 5 50 msec. Mch 3 Priority memory channel scan Mch 2 e Push [D·CLR] to stop the scan. Mch 4 Mch 5 VFO frequency 145. 20 MHz 5 sec. Memory scan Priority channels Mch 1 50 msec. Mch 199 Mch 6 SKIP 30 SCAN OPERATION 8 Memory scan NOTE: Scan edges, 1A­3A/1b­3b, must be programmed in advance. 22) If identical frequencies are programmed into the scan edges, programmed scan will not proceed. Memory scan repeatedly scans all programmed memory channels, except those set as skip channels. q Push [C·MR] to select memory mode, if necessary. · "X" appears. · See below to select bank scan. w Push [A·FUNC] and [5·SCAN] to start the scan. Y Z · To change the scan direction, push [Y] or [Z]. · When [VOL] is assigned as tuning dial, rotate [VOL] to change the scan direction. 14, 65) Push MONI PWR A FUNC B CALL C MR D CLR 8 A FUNC SCAN 5 TONE 1 P. BEEP 2 T. SCAN 3 BANK e Push [D·CLR] to stop the scan. DUP 4 SCAN 5 SKIP 6 OPT 0 PRIO 7 SET 8 H/M/L 9 ENT · Bank scan --Select the desired bank in step q above. q Push [A·FUNC] and [#·BANK] to select memory bank mode. w Rotate [VOL] to select the desired bank, A to J. e Push [·ENT ] (or [D·CLR]) to select the bank. 31 8 SCAN OPERATION Skip channels In order to speed up the scan rate, you can select memory channels you don't wish to scan as skip channels. q Push [C·MR] to select memory mode, if necessary. · "X" appears. Priority watch Priority watch checks for signals on "priority channels" while operating on a VFO frequency. D Memory or call channel watch While operating on a VFO frequency, memory or call channel watch monitors for signals in the selected memory or call channel every 5 sec. e Push [A·FUNC], then push [7·PRIO] to start watching. w Select a memory channel to set as a skip channel. ePush [A·FUNC] and [6·SKIP] to toggle the skip setting ON and OFF. · "SKIP" appears when the channel is set as a skip channel. Push A FUNC SKIP 6 "SKIP" appears · VFO is displayed, then the decimal point ". ", on the frequency readout blinks. · When the signal is detected on the priority channel, the watching is suspended according to the setting of the scan resume condition. VFO frequency Memory channel 5 sec. 50 msec. r Push [D·CLR] to stop watching. 32 SCAN OPERATION D Memory scan watch While operating on a VFO frequency, memory scan watch monitors for signals in each memory channel in sequence, every 5 sec. q Push [C·MR] to select memory mode, if necessary. · "X" appears. 8 Scan resume condition USING SET MODE wPush [A·FUNC], then push [5·SCAN] to start the memory scan. e Push [A·FUNC], then push [7·PRIO] to start the watching. · VFO is displayed, then the decimal point ". ", on the frequency readout blinks. · When the signal is detected on the priority channel, the watching is suspended according to the setting of the scan resume condition. VFO frequency Mch 3 Mch 2 Mch 1 When a signal is received during scanning, the scan resume condition determines what action the transceiver takes. [. . . ] · HM-128L EARPHONE-MICROPHONE You can clip the microphone with PTT switch to your lapel or breast pocket. Includes VOX, PTT and "one-touch" PTT with time-out timer. 15 16 77 16 OPTIONS · VS-1L PTT/VOX UNIT+HS-94/HS-95/HS-97 HEADSET VS-1L PTT/VOX UNIT Required when using these headsets. HS-94 EAR-PIECE TYPE HEADSET Earhook headset with flexible boom microphone. HS-95 NECK-ARM TYPE HEADSET Behind-the-head headset with flexible boom microphone. [. . . ]

DISCLAIMER TO DOWNLOAD THE USER GUIDE ICOM IC-U82

Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets...
In any way can't Lastmanuals be held responsible if the document you are looking for is not available, incomplete, in a different language than yours, or if the model or language do not match the description. Lastmanuals, for instance, does not offer a translation service.

Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual ICOM IC-U82 will begin.

Search for a user manual

 

Copyright © 2015 - LastManuals - All Rights Reserved.
Designated trademarks and brands are the property of their respective owners.

flag