User manual ICOM IC-V201

[. . . ] We want to take a couple of moments of your time to thank you for making your IC-V201 your radio of choice, and hope you agree with Icom's philosophy of "technology first. " Many hours of research and development went into the design of your IC-V201. IMPORTANT READ ALL INSTRUCTIONS carefully and completely before using the transceiver. SAVE THIS INSTRUCTION MANUAL-- This instruction manual contains important operating instructions for the IC-V201. EXPLICIT DEFINITIONS DEFINITION Personal injury, fire hazard or electric shock R WARNING!CAUTION NOTE Equipment damage may occur. No risk of personal injury, fire or electric shock. WORD D FEATURES 75 W* of high transmit output power (except Taiwan version) Front mounted speaker for clear audio readability Tone squelch, DTCS squelch standard Dual color (amber & green) LCD backlight Remote control microphone available (optional for some versions) Optional DTMF decoder i Icom, Icom Inc. [. . . ] w Push [MW(S. MW)] momentarily. · "M" indicator and "­ ­" indication blink, and shows VFO conditions. 5 MR/CALL MW [Y]/[Z] z Select the memory/call channel to be transferred. Push [MR/CALL] to select memory mode, then select the desired memory channel via [Y]/[Z] or keypad. x Push [FUNC], then [CLR A(MW)] momentarily. · "M" indicator and "­ ­" indication blink, and shows VFO conditions. 5 e Rotate the tuning dial to select the target memory channel. · "C" blinks when the call channel is selected. · Scan edge channels, 1A/1b, 2A/2b, 3A/3b, can also be selected. r Push [MW(S. MW)] for 1 sec. to transfer the selected memory/call channel contents to the target memory. · The targeted memory and transferred contents are indicated. c Push [Y]/[Z] to select the target memory channel. · "C" blinks when the call channel is selected. · Scan edge channels can also be selected. · The keypad cannot be used for the selection. v Push [FUNC] then push [CLR A(MW)] for 1 sec. to transfer the selected memory/call channel contents to the target memory. · The targeted memory and transferred contents are indicated. [EXAMPLE]: Transferring memory channel 30 contents to channel 31. Front panel operation: Select the memory channel, then push MW S. MW . Select the target channel. Push MW S. MW for 1 sec. HM-133V operation: Select the memory channel, push then push . Push then push for 1 sec. 28 5 MEMORY OPERATION I Memory clearing Contents of programmed memories can be cleared (blanked), if desired. q Push [V/MHz(SCAN)] to select VFO mode. w Push [MW(S. MW)] momentarily. · "M" indicator and the memory channel number blink. r Push [MW(S. MW)] momentarily, then push [MW(S. MW)] again for 1 sec.  This operation must be performed within 1. 5 sec. · 3 beeps sound, then the frequency is cleared. w Push [BANK(OPT)]. · "­ ­" indication blinks as follows. MW BANK/OPTION z Push [MR/CALL] then select the desired memory channel via [Y]/[Z] or keypad. x Push [BANK/OPTION]. · "­ ­" indication blinks. c Push [BANK/OPTION] again to set the channel to bank setting stand-by condition. · "­ ­" indication stops blinking. [Y]/[Z] e Push [BANK(OPT)] again to set the channel to bank setting stand-by condition. · "­ ­" indication blinking stops. v Push [FUNC] then [CLR A(MW)] then push [Y]/[Z] to select the desired bank to be set. · "M" and bank initial blink. r Push [MW(S. MW)] then rotate the tuning dial to select the desired bank to be set. · "M" and bank initial blink as follows. b Push [CLR A(MW)] to set the channel into the bank. · "M" and bank initial stops blinking. n Push [BANK/OPTION] twice to return to regular memory channel condition. m Repeat steps z to n to set an another memory channel into the same or another bank. t Push [MW(S. MW)] again to set the channel into the bank. · "M" and bank initial blinking stops. y Push [BANK(OPT)] twice to return to regular memory condition. u Repeat steps q to y to set another memory channel into the same or another bank. 33 MEMORY OPERATION 5 I Transferring bank contents Contents of programmed memory banks can be cleared or transferred to another bank. INFORMATION: Even if the memory bank contents are cleared, the memory channel contents still remain programmed. q Select the desired bank contents to be transferred or erased. Push [M/CALL(PRIO)] to select memory mode. Push [BANK(OPT)] then rotate the tuning dial to select the desired memory bank. · Bank initial blinks. y Repeat steps q to t for transferring or erasing an another banks contents. Push [BANK/OPTION] then select the desired memory bank via [Y]/[Z]. Push [BANK/OPTION] to select the bank then select the desired contents via [Y]/[Z]. [. . . ] 12 · Priority watch is paused on the watching fre- microphone keypad lock function. 44 · Push [M/CALL(PRIO)] to cancel the watch. quency. 71 MAINTENANCE 13 -- PROBLEM POSSIBLE CAUSE SOLUTION REF. Some memory channels · The input channel number has not yet been pro- · Rotate the tuning dial to check whether the chancannot be selected via the grammed. · Set the squelch to the threshold point. [. . . ]