User manual ICOM IC-V85

[. . . ] INSTRUCTION MANUAL FM TRANSCEIVER iV85 iV85E iV85-T This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. FOREWORD Thank you for purchasing this Icom transceiver. The IC-V85 FM TRANSCEIVER is designed and built with Icom's superior technology and craftsmanship. With proper care, this transceiver should provide you with years of trouble-free operation. [. . . ] t Push and hold [PTT] to transmit, then speak into the microphone. · Do not hold the microphone too close to your mouth or speak too loudly. y Release [PTT] to receive. PWR A FUNC TONE B CALL P. BEEP C MR T. SCAN D CLR BANK 1 DUP 2 SCAN 3 SKIP OPT 4 PRIO 5 SET 6 H/M/L 0 ENT 7 8 9 D To set the squelch level While pushing [MONI], push YZ [Y]/[Z] to set the squelch level. · The squelch level "10" is tight squelch, "1" is loose squelch and "0" is open squelch. · When [VOL] is assigned as tuning dial, rotate [VOL] while pressing [MONI]. 18, 53) Monitor function MONI PWR A FUNC TONE B CALL P. BEEP C MR T. SCAN D CLR BANK This function is used to listen to weak signals without disturbing the squelch setting or to open the squelch manually even when mute functions such as the tone squelch are in use. Push and hold [MONI] to monitor the operating frequency. The [MONI] key can be set to `sticky' operation in SET MODE. See page 55 for details. INITIAL 1 DUP 2 SCAN 3 SKIP OPT 4 PRIO 5 SET 6 H/M/L 0 ENT 7 8 9 19 BASIC OPERATION 4 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 Display type USING INITIAL SET MODE "Channel Name Indication" type The transceiver has 3 display types to suit your operating style during memory mode operation. The display type is selected in INITIAL SET MODE (p. "Frequency Indication" type Displays memory channel name you have assigned. In this display pre-programmed memory channel names are displayed. "Channel Number Indication" type · Programmed frequencies are indicated when you have not preprogrammed the channel names in the selected memory channel. · Push and hold [MONI] to display the operating frequency. Key lock function Displays memory channel number. In this type only preprogrammed memory channel numbers are displayed. VFO mode cannot be selected. · When the channel indication type is selected, only the following functions can be performed. 32) - Key lock function (see next set of instructions) - Scan pause timer setting, function key timer setting and LCD backlight setting in SET MODE (p. 49) The key lock function prevents accidental frequency changes and function activation. Push [FUNC] then push and hold [ ]( ENT) for 1 sec. to toggle the function ON and OFF. PWR A · " " appears while the lock function is activated. · [PWR], [PTT], [VOL] and [MONI] can be operated regardless of this setting. A FUNC TONE B CALL P. BEEP C MR T. SCAN D CLR BANK FUNC 1 DUP 2 SCAN 3 SKIP OPT 4 PRIO 5 SET 6 H/M/L 0 ENT 7 8 9 ENT 4 BASIC OPERATION Weather channel operation (USA version only) D Weather channel selection q Push [MR] several times to select weather channel group. w Turn the weather alert function ON in SET MODE. Push [FUNC] and [SET](8) to enter SET MODE. [. . . ] The displayed frequency is · The CPU malfunctioned. · External factors caused a fault. Can not charge the battery · Turn the transceiver's power ON. · Remove and re-attach the battery pack or battery p. [. . . ]