User manual ICOM IC-W31E SERVICE MANUAL

[. . . ] WORD SAVE THIS INSTRUCTION MANUAL -- This instruction manual contains important operating instructions for the IC-W31ET/S VHF TRANSCEIVERS and IC-F4062T/S UHF TRANSCEIVERS. Icom, Icom Inc. and the logo are registered trademarks of Icom Incorporated (Japan) in the United States, the United Kingdom, Germany, France, Spain, Russia and/or other countries. i TABLE OF CONTENTS IMPORTANT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . i EXPLICIT DEFINITIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . i TABLE OF CONTENTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] r Push [TX Code CH Select] again to return to the operating channel number indication. USING [TX CODE CH UP]/[TX CODE CH DOWN] KEY: If the transceiver has a [TX Code CH Up] or [TX Code CH Down] key assignment, the programmed TX code channel can be selected directly when pushed. NOTE for PMR or BIIS PMR operation: · The LCD indication does not change when the operating channel number (or name) is displayed. (Depending on the pre-setting) · To check the selected TX code, push [TX Code CH Select]. w Push and hold [TX Code CH Select] for 1 sec. e Push [TX Code CH Select] to select the desired digit to be edited. · The digit to be edited blinks. r Push [CH Up], [CH Down] or 10-keypad* to set the desired digit. t Push [TX Code CH Select] to set the digit. The digit to the right will blink automatically. · When the 10-keypad* is used for setting, the digit to the right will blink automatically without pushing [TX Code CH Select]. y Repeat r and t to input all allowable digits. u Push [Call] or [PTT] to transmit the edited TX code. *IC-W31ET/IC-F4062T (10-key type) only 14 BASIC OPERATION USING [TX CODE ENTER] KEY: q Select the desired TX code channel via [TX Code CH Select]+[CH Up] or [CH Down], [TX Code CH Up] or [TX Code CH Down]. w Push [TX Code Enter] to enter the TX code edit mode. e Push [TX Code Enter] to select the desired digit to be edited. · The digit to be edited blinks. 3 D DTMF transmission If the transceiver has [DTMF Autodial] assigned to it, the automatic DTMF transmission function is available. TO SELECT A TX CODE: q Push [DTMF Autodial]-- a DTMF channel appears. [P3]; TX Code Enter : Push to enter the ID code edit mode directly for both 5-tone and BIIS. T · "TXCE" is displayed on the key indicator. CALLING 0500 CALL BIFN TXC TXCE [Emer]; Null [Side1]; Moni(Audi) : No function is assigned. : Push this key after the communication to send a `Clear down' signal during BIIS channel operation. [Side2]/[Side3]; CH Up/Down : While in the standby condition, selects the operating channel. After pushing [Digital Button] or [TX Code CH Select], selects call list or TX code channel, respectively. w Push and hold [PTT], then speak into the microphone at a normal voice level. · TX indicator lights red. e Release [PTT] to return to receive. · BUSY indicator lights green while receiving a signal. r To finish the conversation, push [Moni(Audi)] to send the `Clear down' signal. · Either station can send a `Clear down' signal. C · "CLR DOWN" is displayed for 2 sec. · " " disappears and the transceiver returns to the standby condition. 17 4 BIIS OPERATION D Displaying the received call record -- Queue indication The transceiver memorizes the calling station ID in the memory. Up to 3 calls can be memorized, and the oldest call record is erased when a 4th call is received. However, once the transceiver is powered OFF, the all records are cleared. q Push and hold [Digital Button] for 1 sec. · Displays following indication. D Group call q When a group call is received; · Beeps sound. · " " appears and the mute is released. G · The programmed text message (e. g. "GROUP") and the calling station ID (or text) is displayed when the indication mode is 2 lines. [. . . ] · MB-96N/96F LEATHER BELT HANGER Battery case for AAA (LR03) × 6 alkaline * 1 Operating periods are calculated under the following conditions; TX : RX : standby = 5 : 5 : 90 * 2 Operating periods depends on the alkaline cells used. D OPTIONAL UNITS · UT-96R 2/5 TONE UNIT · UT-109R /UT-110R SCRAMBLER UNITS Non-rolling type (UT-109R)/Rolling type (UT-110R) voice scrambler unit provides higher communication security. D CHARGERS ·BC-119N DESKTOP CHARGER + AD-106 CHARGER ADAPTER + BC-145 AC ADAPTER For rapid charging of battery packs. An AC adapter is supplied with the charger depending on versions. ·BC-121N MULTI-CHARGER + AD-106 CHARGER ADAPTER (6 pcs. ) + BC-157 AC ADAPTER For rapid charging of up to 6 battery packs (six AD-106's are required) simultaneously. An AC adapter should be purchased separately. [. . . ]