User manual ICOM ID-800H

[. . . ] INSTRUCTION MANUAL ID-800H VHF/UHF DIGITAL TRANSCEIVER This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. FOREWORD Thank you for purchasing this Icom product. The ID-800H VHF/UHF DIGITAL TRANSCEIVER is designed and built with Icom's state of the art technology and craftsmanship. With proper care, this product should provide you with years of trouble-free operation. [. . . ] x Push [FUNC], [CLR A(MW)] momentarily, YZ then push [Y]/[Z] to select the memory channel to receive the transferred information. YZ · To transfer to the VFO, push [Y]/[Z] to select "-- -- --". 5 6 MR/CALL [M/CALL·PRIO] "C1" or "C2" appears MW MR/CALL Push and hold [MR/CALL] for 1 sec. to select the call channel mode then push [BAND] to select the desired call channel in the main band. · Push [MR/CALL] to select memory mode, or push [VFO/LOCK] to select VFO mode. [Y]/[Z] BAND c Push [FUNC], and then push and hold [CLR A(MW)] for 1 sec. to transfer the contents. INFORMATION When the VFO mode is selected from the call channel, a small "c" appears instead of memory channel number. 40 6 CALL CHANNEL OPERATION Programming a call channel Operating frequency, duplex information, subaudible tone information (tone encoder or tone squelch ON/OFF and its frequency) can be programmed into the call channel. q Set the desired frequency in VFO mode. Push [V/MHz·SCAN] to select VFO mode. e Rotate [DIAL] to select the desired call channel. · "!" indicator and "C1" or "C2" blink. VFO/LOCK MW [Y]/[Z] z Set the desired frequency in VFO mode. x Push [FUNC], then [CLR A(MW)] momentarily. Y Z c Select the call channel via [Y] or [Z]. v Push [FUNC], and then push and hold [CLR A(MW)] for 1 sec. to program. · 3 beeps sound and the unit returns to VFO mode automatically. r Push and hold [S. MW·MW] for 1 sec. to program. · 3 beeps sound and the unit returns to VFO mode automatically. [EXAMPLE]: Programming 145. 120 MHz into the call channel 2 via the microphone. Push to select VFO mode. Push , then . Push until "C2" appears. Push , then push for 1 sec. " "Beep " Beep " Beep " 41 SCAN OPERATION Scan types Scanning searches for signals automatically and makes it easier to locate new stations for contact or listening purposes. 7 There are 3 scan types and 4 resume conditions to suit your operating needs. BAND SCAN (p. 43) Band edge Scan Band edge Repeatedly scans all frequencies over the entire band. Used as the simplest scan without any preliminary settings necessary. PROGRAMMED SCAN (p. 43) Start 1A 2A 3A 4A 5A End 1B 2B 3B 4B Band 5B edge Band edge Scan edges Jump Scan Jump Repeatedly scans between two user-programmed frequencies. Used for checking for frequencies within a specified range such as repeater output frequencies, etc. 5 pairs of scan edges are available and scans 1A­1B (P1), 2A­2B (P2), 3A­3B (P3), 4A­4B (P4), 5A­5B (P5). 4 resume conditions are available: 3 timer scans and pause scan. When receiving a signal, pause scan pauses until the signal disappears; timer scans pause for 5, 10 or 15 sec. 6 7 MEMORY SCAN (p. 43) SKIP M2 M1 M 500 M7 M6 M3 M4 M5 SKIP Repeatedly scans memory channels except those set as skip channels. Used for oftencalled channels and for bypassing normally busy channels such as repeater frequencies. SCAN RESUME CONDITION (p. [. . . ] 95) · Data speed for DV mode (p. 96) : Push : Push · DTMF speed (p. 98) (front panel); or (front panel); or (microphone) (microphone) · Squelch delay (p. 96) *Available in the USA version only. 15 · Narrow transmission (p. [. . . ]